Register To Comment
Page 70 of 169 FirstFirst ... 2060686970717280120 ... LastLast
Results 691 to 700 of 1682

Thread: How Could I Improve...

  1. #691
    Guest
    Thanks Leo

  2. #692

  3. Overweight

  4. #694


  5. LMAO. I seriously LMAOed after reading that. Shaving off a mm of Hardox wont help. Youre seriously going to have problems with a bot that has a crusher, 4mm Hardox armour, and 2 LEM130s, really. Ditch the LEMs for S28-400s, and give your bot around 5-8mm titanium. Also, what powers the arms on the sides?

    Shape: A very low wedge with side skirts
    Dimensions: 94cm X 75cm X 42cm


    Is that height the top of the crushing beak?

  6. #697

  7. Looks kind of overweight to me...as far as I remember, Razers arms were attached to the main claw by hinges, and when the arm was raised fully a bit of string (steel cable) pulled the hinge down so they went upwards...doing something like that would save weight, if not necessarily be 100% reliable.

    While Im here (again...), can I be annoying and ask for opinions on my reincarnated Fire And Ice?

    Phoenix Down
    WEIGHT: Depends on setup, but around 110kgs
    DIMENSIONS: 85 x 60 x 25 cm
    SHAPE: Invertible long box, with a wedge at the front and an inverted wedge at the rear. The wedges are shallower in this version for more wedging goodness.
    COLOUR: Largely midnight blue, fading to black at the rear and yellow at the front, with flashes of orange and red.
    DRIVE: 2 LEM200 motors running from 4 NiCad packs at 48v, driving titanium tank tracks with Vulkalon on every other link for grip without eating amps
    SPEED: 16mph average, 25mph max (rarely used as it is difficult/impossible to turn at this speed)
    GROUND CLEARANCE: 10mm at sides, plating extending below both wedges giving zero clearance on whichever side is down (if that makes sense...), 25cm at rear.
    ARMOUR: Sides, front and rear are 6mm Hardox, top and underside are 6mm titanium with Lexan reinforcing in key areas all around.
    WEAPONS: Primarily a rambot, and is assisted by 4 10cm hardened steel spikes, one either side of each wedge. In the middle of both wedges, there is an interchangable weapons bay, which can hold the following:
    Claw: A hardened steel hydraulic cutting/crushing claw, no taller than the robot, powered from a Vivoil pump at 2400psi giving about 4 tonnes of force at the ram, and 2 tonnes at the tip of the claw, which wont cut into good titanium or Hardox but will prevent almost anything from escaping.
    Saw: A 15cm diameter diamond edged circular saw, run from an S28-150 Magmotor at 24v to around 3500rpm, spinning upwards to have a lifting effect.
    Lifter: A pair of Haardvark/Nidhogg style hardened steel lifting forks, powered by an S28-150 Magmotor and a custom gearbox that can lift about 100kgs rather easily.
    Standard setup is the claw at the front, and a saw at the back.
    The weapons bay can be covered over to just make it a rambot - this has the advantage of making it just under 100kgs, allowing me to do battle in tournaments that dont have a tracks weight bonus.
    SRIMECH: None, but runs inverted and has spike strips on the sides to stop it stranding itself.
    NOTES: Armour and components shock mounted to reduce damage from impacts, spinners, bashes, battles, and other things ending in S.
    STRENGTHS: Good speed and power, good against spinners, versatile weaponry
    WEAKNESSES: Crushers and very powerful axes could cause problems with the tracks.

  8. #699
    davids
    Guest
    quote:

    Turning Circle: Guess.

    10 metres?
    200 metres?
    0?
    Negative 5?
    42?

    (Message edited by DavidS on April 12, 200

  9. #700
    42 must be the answer.

Register To Comment

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •