Velociraptor's Fanfic Tournament - Series 7!

[knightrous]

Infusion
Motivation: 4 x 125mm wheels
Speed: 0-12MPH [25MPH under Kinetic Boost]
Clearance: 7.5mm (same inverted) 0mm at the front, the wedge scraps the floor.
Weight: 100kg
Height: 125mm
Length: 800mm
Width: 600mm
Weapon: The weapon is a 31kg Hardox spinning ring (Ala MDU) powered by a LEM170 @ 36v. The rim rotates at 1800rpm and should spin up within 2-3 seconds max. The weapon is also a storage device for the drive. The spinning rim is connected to each side of the drive via a car air conditioner clutch, when the clutches are engaged, the 31kg kinetic storage bank(the spinning rim) transfers its energy into the drive train, giving it approximately double torque and speed for 2-3 seconds until the rim starts too loose speed and energy. This extra €˜kinetic€™ boost is used to ram into opponents with the front 10mm thick Hardox 500 wedge (similar to the one on Warrior SKF but wider and less depth to it). The front wedge is rubber shock mounted to ensure it survives the biggest of hits.
Drive: 2 x C40-500 Magmotors on 36v geared 7.5:1. The drive is also assisted via the spinning rim as explain above.
Batteries: 90 x 3600mAh NiCD Cells configured into 3 x 36v packs. This gives an output of 36v @ 10.8Amp/hours.
Armour: Front wedge is made entirely out of 10mm Hardox 500, the top and bottom of the robot is made out of 8mm Titanium/Vandium, The ring is made out of 10mm Hardox 400 with inner bracing to the perimeter bearing. Inner bulk heads are made from 20mm polycarbonate and 10mm aluminium.
Notes: Invertible, and generally well controlled for a spinner.

[dogbot4000]

if theres any places left and if you are allowed real robots then Ill pick spartacus

[velociraptor]

There are four places left, Tim, and real robots are allowed, but you need to enter eight robots.

(Message edited by velociraptor on October 10, 2005)

[velociraptor]

I still need stats from Martijn, Daniel, Martyn and AJ.

I also need confirmed entrants in the following events from the following people:
MW: Tony (but hes got an excuse), AJ, Aaron, Alex M
LW: Tony, AJ, Aaron, Alex M
FW: Same four people
AW: Same again
SHW: Steven, AJ, Alex M
Annihilator: Dave Westons second entry, AJ, Martijn, Alex M
Challenge Belt: AJ, Alex M
HRR: AJ, Alex M

[siphai]

Ive got my SHW, AW, and MW done. Plus Ive finished CADing my FW, and stats for that will be up shortly. Now to finish my LW...

[majinb]

Heres three of my vapours, four to go:

Name - A Night at the Bar

Shape - A wide cylinder-shaped axlebot

Weight - 100 Kilogram

Speed - 24 km/h (15mph, geared for control)

Dimensions - 25x110x25 cm

Ground Clearance - Well, it€™s an axlebot€¦

Power - 2 S28-400 Magmotors at 24 volt

Movement - Two axlebot wheels, 25cm diameter

Turning Circle - Zero

Weaponry - In the middle of the cylinder, at 5 cm above the floor, is a 60 cm hardox bar with thick tungsten teeth on it. It weighs 25 kilogram and is powered by a B42-500Magmotor at 36 volt, spinning at 2000 rpm, giving it a nice spin up time. It€™s able to poop 55 kJ of energy straight into any opponent, so ha! The bar is mounted in such a way that it sticks out from the front and from the back, basically making it a double-headed spinning bar.

The only reason my bot can keep on driving normally even though it has only two wheels on the floor is because the centre of gravity is somewhere near the middle of the two teeth.

Armour - If you split the cylinder in halve, horizontally, the upper part of it is 4,5 mm hardox, and the lower part 5 mm, which is to centre the weight around the lower part, which is needed for the srimech. The insides are made shockproof with rubber, so it won€™t be destroyed by it€™s own weapon.

Srimech - Seeing there is a huge bar spinning in front and at the back of the bot, chances are a wedge won€™t be able to get underneath it from there anyway.
IF it is flipped, the bar will stop spinning and glide inside the cylinder, where it perfectly fits. At that point the bot is an almost perfect cylinder, and will be able to roll. The centre of gravity will roll in such a way that it will point downwards. As I designed it, the centre of gravity should be somewhere in the middle of the tungsten teeth, therefore it will roll to the position shown on the pick, and the bar will be put on again.

Strenghts - Devastating weaponry sticking out at the front and back, at only 5 cm above the floor. Should be able to fend off wedges.
Weakness - Can bounce off though armour, or the arena wall, or even the arena floor when the cylinder topples. And seeing my ONLY contact with the floor is the two wheels, this might become a rocking chair on steroids. Won€™t be pushing very much either.

Here€™s a pic; http://jupiter.walagata.com/w/madbull/Bar.gifhttp://jupiter.walagata.com/w/madbull/Bar.gif

Name - Axe to Fall

Shape - Take a cylinder, cut it in halve, and then put it on the ground, rectangular side heading downwards. The straight ends are the left and right sides, and are sloped. (Well, just take a look at the picture =P )

Weight - 100 Kilogram

Speed - 24 km/h (15 mph)

Dimensions - 115x80x40 cm (due to axe hanging out, main body is 80x80x40 cm)

Ground Clearance - 0 at front, 7 mm anywhere else

Power - 2x LEM130s at 48v

Movement - Four inner wheels, 10cm diameter

Turning Circle - Zero

Weaponry - The main weapon is a 5 kg double-headed axe on top of the machine, it€™s a steel 80 cm shaft with two diamond edged blades made of hardox on the end of it. The blades are shaped like the Mortis€™ blades, in order to create some nice slices into opposing armour.
The whole axe is powered by 2 nitrogen bottles at 1000 psi, a 1 kg buffer bottle and a 30 mm bore ram, for fast and furious hits, with a downforce of almost 2 ton brought onto a fine blade, and an energy unleash which seems significantly higher than for example Beta€™s if my calculations are right.

At the front of Axe to Fall is a small wedge/ram made out of 8 mm Titanium, to lift my opponent€™s wheels into air while clobbering them with my blade, or perhaps even to grab him. This ram is also my plan B if my axe fails in battle, just ram them hard using my good traction.

Armour - 8 mm Titanium front and 15 mm polycarb for the rest of the bot.
There are also two small blocks of vulcanized rubber on the mid-front and the mid-back of my machine, to absorb the downforce where the axe hits the chassis.


Srimech - The axe acts as a srimech, thanks to the curved shape of the top my bot can self right in no time, even if it has to self right over the wedged front (the wedge is very small mind you).
To make sure my bot won€™t end up on his side, I created a pair of curves on both sides, as can be seen on the picture.

Strengths - Destructive weapon, quick at self righting
Weakness - Weapon only works when opponent is in front of or behind the machine.

http://jupiter.walagata.com/w/madbull/Axe2.gifhttp://jupiter.walagata.com/w/madbull/Axe2.gif

Name - Back to Rock II

Shape - A box with a slightly sloped front

Weight - 100 Kilogram

Speed - 29 km/h (18mph)

Dimensions - 90x75x30 cm

Ground Clearance - 0 at sides and front, 2 mm at the back

Power - 2x Etek motors at 48 volt

Movement - Four wheels, 20cm diameter

Turning Circel - Zero

Weaponry - It has a broad hydraulic lifting arm which can easily lift 200 kg. To easily get underneath an opponent, it has two lifting plates at the bottom of the arm, one on the left end and one on the right end, instead of one large lifting plate like Behemoth.

Between the two plates, in the centre of the scoop, I mounted a vertical diamond edged Pussycat-style blade, powered by a S28-150 Magmotor, spinning upwards at approximately 3000 RPM, which will hopefully rip off some armour, or more likely, a tire, while lifting an opponent. Jamming a blade into an opponent while lifting it hopefully provides as much control over an opponent than a Behemoth-style grabbing claw/axe can, and it€™ll surely do more damage. (To avoid confusion, the blade is actually part of the lifter, so when the lifter moves up, the blade moves along).

On both sides of the bots is a pair of 5 mm titanium skirts, to make sure I won€™t get flipped very often, as hydraulic srimechs just aren€™t as fast as pnuematic ones.

Armour - 6 mm titanium all around

Srimech - The lifter self-rights the robot when needed

Strenghts - Nice weapon synergy, high traction, low ground clearance
Weakness - Hydraulic srimech might prove to be slow

A picture can be found here: http://jupiter.walagata.com/w/madbull/BacktoRockII.gifhttp://jupiter.walagata.com/w/madbull/BacktoRockII.gif


Ill enter Back to Rock II for the House Robot Rebellion
A Night at the Bar will be one of my two entries for the annihalator

[team_britespark]

Soz, havent had a lot of time cos of school. Ill stick with my VFT6 entrants if I can, and Ill have a random realie

[velociraptor]

Thats OK, Daniel. The realie you entered last time was Mr Nasty - do you want to enter that this time or a different one?

[dogbot4000]

Because I know how crap my bots are Ill enter 8 realies
wheely big cheese
flippa
spartacus
pulverizer
gravity
tough as nails
snake bite
and rambot
wheely big cheese, rambot and tough as nails for the annihlator(if theres any spaces left

(Message edited by dogbot4000 on October 11, 2005)