• Ocracoke's Avatar
    Yesterday, 15:16
    Hahahaa! It might be made to be scared a little sooner than I thought. I found some 90mm long bolts that will work as drive shafts and the shaft mounts will take a M6 bolt without adaptation (they...
    210 replies | 138054 view(s)
  • Ocracoke's Avatar
    17th February 2020, 23:21
    Following on from the last post, I've been busy. Tada! I'll be running out tomorrow to get some M10x100mm bolts or something to screw the motor mounts down with along with some coarse...
    210 replies | 138054 view(s)
  • Ocracoke's Avatar
    17th February 2020, 01:24
    Jibril So yeah, this weekend didn't go to plan. Managed to get the drive templates made but in cutting the drive shafts, need to go outside to that really and it has been too wet to do so. Still, I...
    210 replies | 138054 view(s)
  • Ocracoke's Avatar
    15th February 2020, 15:00
    We'll see closer to the time. Had a bit of a setback here which means I can't work on it this weekend. It'll happen.
    7 replies | 478 view(s)
  • Ocracoke's Avatar
    13th February 2020, 13:48
    Nope, no deadline really. Signups are open up until the event starts.
    7 replies | 478 view(s)
  • Ocracoke's Avatar
    13th February 2020, 10:06
    Excellent, glad to hear the event is being looking forwards to! With any luck, I will have the arena's floor lifted up a little over the weekend and the pit floor painted.
    7 replies | 478 view(s)
  • Ocracoke's Avatar
    10th February 2020, 22:41
    Hahahaa, true enough! I've got a 10mm spade bit somewhere, will bear that in mind for future use.
    210 replies | 138054 view(s)
  • Ocracoke's Avatar
    10th February 2020, 12:14
    It is time for the next BotFest event! Location St. Lukes Church Poulton Wallasey CH44 3BD Date 25th April 2020
    7 replies | 478 view(s)
  • Ocracoke's Avatar
    10th February 2020, 02:41
    Jibril The HDPE base panel has been drilled. Doing 32 holes three times over in 3, 8 and 10mm bits is nuts but there you are. Currently mocking up the motor mount bolt pattern on a 1mm sheet of...
    210 replies | 138054 view(s)
  • Ocracoke's Avatar
    9th February 2020, 00:13
    Ocracoke replied to a thread BOB FW Series in Build Diaries
    I'd recommend something thicker, like the thread cutting oil that Colin mentioned. WD40 is probably going to be too light for this.
    101 replies | 24367 view(s)
No More Results
About Maxamuslead

Basic Information

Date of Birth
January 1, 1994 (26)
About Maxamuslead
Name:
Mark Smith
Location:
Lincolnshire, Threekingham
Interests:
geeky stuff
Occupation:
Network Technician
Robots:
"Blacksmith" (FW) in a bag in bits "Forge Master" (FW) battle worn "Forge Master II" (FW) in CAD

Statistics


Total Posts
Total Posts
454
Posts Per Day
0.43
General Information
Last Activity
13th February 2020 10:36
Join Date
6th April 2017
Referrals
0

4 Friends

  1. Al_ 
    Status
    Offline

    Roboteer

    Al_
  2. James Williams 
    Status
    Offline

    Roboteer

    James Williams
  3. Ocracoke 
    Status
    Offline

    Team Kaizen

    Ocracoke
  4. R9000 
    Status
    Offline

    Member

    R9000
Showing Friends 1 to 4 of 4