Register To Comment
Page 3 of 12 FirstFirst 12345 ... LastLast
Results 21 to 30 of 120

Thread: Team Health & Safety - First Time Builder

  1. #21
    Hi Greg. Looking forward to seeing what you come up with, I had quite a chuckle reading through that .
    Those motor mounts do look really strong and beefy, I guess it depends where you want the compromise between weight and strength to be. I can show you what I've done for mine so far (and by no means am I right) I used a hole drilled into the HDPE chassis that snugly fits the motor with a polycarb plate (what I had available) on the front using the standard bolt holes. Probably weaker, but hopefully a little flex if there is any may prevent something else breaking elsewhere (that's my story and I'm sticking to it!)
    20161016_170540.jpg

  2. #22
    Zenith's Avatar
    Roboteer

    I like your solution a lot. I think I'll do the honorable job of stealing the idea.

    I suppose those hex extenders are readily available online somewhere? I could do with some extra reach (on the axles, I mean...you dirty people).

  3. #23

  4. #24
    The hubs I'm using are these ones, as I'm running 1/10 scale rc car wheels and tyres, I think thats why they are a bit longer.
    http://www.technobotsonline.com/polo...k-of-2-en.html

  5. #25
    Zenith's Avatar
    Roboteer

    It seems the gaps between updates seem to be of an increasing nature. I guess it just builds on the hype.

    The past few months saw the development of me entering the realm of stepfatherhood, and with it, also initiating the subsequent indoctrination of a 6 year-old into the art of robotic combat. Attacking mommy's slippers with the Viper apparently fed the bug to such an extent that the good lad wanted an R/C car for Christmas. Good thing I've got a direct hot line to the North Pole.

    You see, apparently the good folks at Nikko have used the past twenty years of my absence to figure out tank drive on their concoctions, which played perfectly into my scheme. Tank drive is the be-all-end-all of our little world.

    IMG_20170105_221633.jpg

    To make a long story short, mommy's slippers no longer suffered the brunt of the attack. It did occur to me though that whereas I know how to fix the Viper, fixing the Nikko tank might be a tad more impossible given how everything is made of that famous CORF (Crack Once Regret Forever) plastic.

    So time to avert my attention again to my own build (because well, that's why you're here isn't it?). I took the time inbetween the training sessions to get a schematic worked out and get the necessary tools lined up. I like figuring out stuff myself, which in turn also sparked the interest of our little raskal.

    IMG_20170105_224656.jpg

    Either that or my drawings are just hilarious. Feel free to point out mistakes and I'll try not to be offended.

    Just wondering what might be a good servo to use for a beetleweight. I noticed that the one in the Viper may very well do the job, but for now, all that counts is getting a driving platform.

    Design wise, I'm looking at a lifter which hides between two scoops up front - with all them spinny thingies out and about in beetleworld I'm not so keen on them munching away at the party piece; as it is, I have no plans to make my lifter out of birthday cake.

    I could put one of those unblowable candles on top though and rename it The Cake Is A Lie, but I guess that breaks FRA regulations.
    Last edited by Zenith; 5th January 2017 at 21:02.

  6. #26
    Zenith's Avatar
    Roboteer

    It surely looks like progress has allowed us a look up her skirt for once!

    The past few weeks saw me satisfying both my inner and outer 6-year-old with some hardcore CAD design. Not the 3D-wizardry kind ofcourse, but the Cardboard-Aided kind. You know you've crossed a certain threshold when you're using the cardboard boxes your bot stuff came in to make your robot mock-ups.

    IMG_20170116_183538.jpg

    Anyways, it finally brings some light at the end of the tunnel for the two sheets of HDPE that are anxiously awaiting their brutal murder trial.

    But this is not all, oh no - with having studied the inner workings of the Viper and drawing up a schematic, I finally had grown sufficient testicular awesomeness to have a go at putting together a working circuit. All the parts were there, now it was time to line them up in the correct 'no-the-square-peg-can't-go-in-the-round-hole' way (this was naturally preceded with me making a removable link first, because HEALTH AND SAFETY PEOPLE).

    This didn't go without a good share of screwing up ofcourse. You might notice that this very much has a 'learn-as-I-go-along' vibe to it, so naturally, there are also embarrassing screw ups. This particular one went like this:

    Step 1: Order BEC plugs.

    Step 2: "Hey, the connectors come separate from the plugs! I have to assemble the plugs myself then"

    Step 3: Proceed to put all the connectors inside the plugs

    Step 4: Wonder why it is so hard to get a wire to stay in there.

    Step 5: Proceed to pry all the connectors out

    Step 6: Look at the connectors, look at the wire, and hear a penny drop.

    Yes, I know. Despite all of this though, I eventually got the following setup ready:

    IMG_20170119_113346.jpg

    Eventually, with Lamb of God blasting a fitting AWAAAAAKENNNNNNNNNNN through the living room, the wheel moved. Here is a reconstruction:



    I immediately felt like I'd popped a roboteering cherry, and felt the need for a cigarette, a shower and a cuddle. However, what I got was some post-orgasmic drama, as the plugs on the ESC would not fit on the receiver of my Spektrum DXe (a Spektrum AR610). This is all because the AR610 has those offset cavities which can't take square plugs.

    Ofcourse, I could just use the HK one from the Viper (which I did for testing), but for the eventual bot I really want to leave the Viper in one piece (the AR610 also seems incompatible with the parts in the Viper by the way).

    I reckon that if I want to learn how to do stuff properly (like making BEC plugs, AMIRITE?), I have to build TINAD from the ground up - using Viper parts in the eventual bot is cheating. And as Taylor Swift will tell you, cheating is bad.

    Next step will be to learn soldering, and tools for that are already on the way. For a driving platform I will need to combine two wires into a single one (like a Y, not like 1+1=1), so it will be interesting to see how that will work out.

    Tips are welcome and will be met with a thunderous applause from behind my computer.
    Attached Images Attached Images
    Last edited by Zenith; 19th January 2017 at 10:50.

  7. #27

  8. #28
    Zenith's Avatar
    Roboteer

    As an expert on being daft I feel nothing but warmth for your reply. It should end up being a beetleweight if everything goes according to plan.

  9. #29
    If you're having trouble with fitting your ESC plugs in your Rx, you can just carefully​ file the corners of the plug off. Just make sure you file them off on the correct side. I have an AR610 too.

  10. #30
    Zenith's Avatar
    Roboteer

    Very well. I shall get to work, and report back for further hilarity. Currently, I am awaiting the arrival of further tools.

Register To Comment

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •