Search:

Type: Posts; User: geeza

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    3
    Views
    1,850

    That document is 5 years old, I believe it was...

    That document is 5 years old, I believe it was taken down as machines have moved on and new guidelines are required. Kane would be able to clarify better.
  2. Replies
    9
    Views
    3,611

    Yes that's the standard, to remove the CO2 nut....

    Yes that's the standard, to remove the CO2 nut. The filling rig will screw straight on to the bottle valve. This is the case a live events and robot wars.

    The dump can be anywhere in the system as...
  3. Replies
    6
    Views
    2,978

    gearsandsprockets.co.uk or bearingboys.co.uk

    gearsandsprockets.co.uk
    or
    bearingboys.co.uk
  4. Replies
    9
    Views
    3,611

    We had someone use this system on RW last series,...

    We had someone use this system on RW last series, I failed them because of it. No part of the system can be pressurised until it is in the arena, the above photo doesn't allow for the system to be...
  5. Replies
    10
    Views
    4,335

    I assume this is to add a fitting to the side of...

    I assume this is to add a fitting to the side of the bottle. I would advise against it, the wall thickness is about 5mm. This is not enough to tap for a decent BSP thread. Then ends of the bottle are...
  6. 234mph Gary :-)

    234mph Gary :-)
  7. Replies
    2
    Views
    1,202

    Glasgow, but I have used them in the past...

    Glasgow, but I have used them in the past
    http://www.airlines-pneumatics.co.uk/
  8. Replies
    8
    Views
    2,183

    Yes the brushes issue is the most common reported...

    Yes the brushes issue is the most common reported fault. Did you have any problems with the movi-motors?
  9. Thread: 2.4 ghz dss

    by geeza
    Replies
    7
    Views
    3,114

    The next most important thing is that the set you...

    The next most important thing is that the set you buy will fail safe to a pre-programmed position not its last known position.
  10. Thread: 2.4 ghz dss

    by geeza
    Replies
    7
    Views
    3,114

    Most modern ones are, I suggest just reading the...

    Most modern ones are, I suggest just reading the site or manufacturer website. Or if buying from a shop just ask.
  11. Replies
    2
    Views
    1,219

    Diode across the solenoid

    Diode across the solenoid
  12. Thread: Bosch 750 24v

    by geeza
    Replies
    3
    Views
    1,498

    Good luck. They are no longer in production, I...

    Good luck. They are no longer in production, I like others have a few spares but with 2 heavies I need to keep them. We are working on a replacement motor (movimotor) but they need some heavy mods to...
  13. Replies
    3
    Views
    1,133

    I have some old packs that you can have.

    I have some old packs that you can have.
  14. Replies
    9
    Views
    2,909

    You will struggle to get Bosch 750s now, there...

    You will struggle to get Bosch 750s now, there are no new ones available in the uk at least.
  15. Replies
    9
    Views
    4,358

    I think a point one way or the other should be...

    I think a point one way or the other should be made by the judges before the comp starts, on the one wheel issue. We all know each design is different, the rules used to state you must be able to...
  16. Obviously confident about Spartan's chances of...

    Obviously confident about Spartan's chances of surviving the champs!
  17. I will bring the smallest gear puller we have a...

    I will bring the smallest gear puller we have a work, most of them are big stuff for cars but hopefully one of the smaller ones is ok. Unless anyone else offers better.
  18. Replies
    494
    Views
    91,011

    I just ran the M5 cut tap down, no need to drill...

    I just ran the M5 cut tap down, no need to drill it out.

    Calum you are right it is 4.65 for a roll tap
  19. Replies
    1,044
    Views
    218,483

    I think there should be a constructors champ as...

    I think there should be a constructors champ as well! I've got 3 in that this year.
  20. Thread: Bungee advice

    by geeza
    Replies
    3
    Views
    1,657

    I used to do a reef knot to make a loop then...

    I used to do a reef knot to make a loop then clamp the loose ends
  21. We usually get a pass so we don't have to pay the...

    We usually get a pass so we don't have to pay the extortionate price for parking, James or grant will confirm this I'm sure.
  22. Replies
    51
    Views
    19,542

    The clamps are to suit standard co2 tanks 117...

    The clamps are to suit standard co2 tanks 117 dia. The small buffers I used were turned down 600g bottles.
  23. Replies
    51
    Views
    19,542

    Oh yes you can chop that bulge off the back if...

    Oh yes you can chop that bulge off the back if you want to, it serves no purpose on with a fp ram in. It was a mod for a lp ram that I did towards the end.
  24. Replies
    51
    Views
    19,542

    I'm sure you have figured it out, but assemble...

    I'm sure you have figured it out, but assemble the motors onto the gb plates first, then put into the bulkheads. Also forgot to say but I would like to keep the name as I've got a new heavy on the...
  25. Replies
    1,044
    Views
    218,483

    Yeah well its who you know, not what you know :-)

    Yeah well its who you know, not what you know :-)
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4