Search:

Type: Posts; User: adamclark

Page 1 of 5 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    11
    Views
    1,646

    It's 8mm HPDE at the moment at least, trying to...

    It's 8mm HPDE at the moment at least, trying to keep as thick as poss. Its aluminium top and bottom.
  2. Replies
    11
    Views
    1,646

    Oooof, just did a full weigh in minus the heat...

    Oooof, just did a full weigh in minus the heat shrink that has to go on the motors and a couple of cable ties, and tis 1g spare. Fortunately I've got a lighter electronic tray to go in, and some...
  3. Replies
    11
    Views
    1,646

    thanks. wiring isnt finalised yet until i get the...

    thanks. wiring isnt finalised yet until i get the motors heat shrunk and fitted with some flexi supports to support the ends. The printed electronic tray has guides built in for the routing of the...
  4. Replies
    11
    Views
    1,646

    Nearly finished, drives around nice, went for the...

    Nearly finished, drives around nice, went for the single stick mixing method in the end. Working out an efficient way to fit the 01 steel dozer blade, then will get it hardened. Although weight is...
  5. Replies
    11
    Views
    1,646

    It might even be ready by then! The botbitz ESC...

    It might even be ready by then! The botbitz ESC got to the UK really quick, but then customs sat on them for about 10 days and RM decided to faux deliver them. Should have my hands on them by friday...
  6. Thread: 259-b

    by adamclark
    Replies
    3
    Views
    882

    For now its just going to be a 4WD shovel....

    For now its just going to be a 4WD shovel. Practice for building and driving. If all goes well then I might have to think about something with a vert spinner, although I always fancied some whyachi...
  7. Thread: 259-b

    by adamclark
    Replies
    3
    Views
    882

    It's also been nutstrip factory time as well....

    It's also been nutstrip factory time as well. 1/4" ally bar and I start out with a stout centre drill to locate the holes so at least the drill doesn't wander, then follow up with a 2.5mm drill and...
  8. Thread: 259-b

    by adamclark
    Replies
    3
    Views
    882

    259-b

    Just realised there is a build diary section ! So here is the beetleweight underway.

    It's based on the trilobyte design but converted a bit into metric, I'm on the way now for a chassis by the...
  9. Replies
    11
    Views
    1,646

    259-B a beetleweight

    I've decided to start a beetleweight, nothing too clever to begin with, just a 4WD based off the Trilobyte design format. I began with the dimensions and then swapped them around a little bit to suit...
  10. Replies
    0
    Views
    928

    retiming N20 gearmotors

    Thought this might be of interest, i have been messing around with a tracked antweight. Currently a pusher with a titanium shovel and N20 gearmotors. They seem to be timed slightly one way making it...
  11. Replies
    196
    Views
    44,206

    If you are getting HPDE to cut by DirectPlastics,...

    If you are getting HPDE to cut by DirectPlastics, or to supply cut pieces make sure you take into account that they can be 3-5mm tolerances (normally under). I managed to get a replacement piece the...
  12. Replies
    62
    Views
    12,264

    Is it fitted with anti-gravity plates?

    Is it fitted with anti-gravity plates?
  13. Replies
    196
    Views
    44,206

    try this, pinion gear removal...

    try this, pinion gear removal
    https://www.youtube.com/watch?v=7pmiOchcTSc&t=4s
  14. Replies
    6
    Views
    1,536

    Well the first step is done. I got a PropDrive...

    Well the first step is done. I got a PropDrive 28-36 and a HK F-60 Sbec and one of those USBASP. Soldered it in (wont be doing that again, going to buy the plug device) and managed at last to get the...
  15. Replies
    6
    Views
    1,536

    Thanks for the tips. But with tz85 showing...

    Thanks for the tips. But with tz85 showing Classic HK out of stock message and all the recs also out of stock I'm putting a banebots order in for a pair of wheels , boxes and shafts and then a HK for...
  16. Replies
    6
    Views
    1,536

    Brushless FW drive setup

    I'm going to setup a demo drive unit using brushless as a learning excercise. The plan is to use some bits for a test chosen I hope so they can be expanded on for different configurations as the...
  17. I've used the ultra small mixer in my quad...

    I've used the ultra small mixer in my quad rovers, and they do work. https://www.thingiverse.com/thing:2687740
  18. Replies
    9
    Views
    3,442

    FYI, the very first antweight ever built was...

    FYI, the very first antweight ever built was constructed using a sherline mini-lathe mill combo.
  19. Replies
    9
    Views
    3,442

    I've got one of the Malyan M200 which has been...

    I've got one of the Malyan M200 which has been superb for the price and been printing almost every day for the last year. With a UK plug its 195 on there, but with a US plug only 117. The actual unit...
  20. Replies
    9
    Views
    2,223

    I have one for actual chopping to save my nakiri...

    I have one for actual chopping to save my nakiri knife
  21. Replies
    294
    Views
    57,796

    https://youtu.be/ixjWLL1au18

    https://youtu.be/ixjWLL1au18
  22. Replies
    294
    Views
    57,796

    A variation on a fauchard would suit quite well...

    A variation on a fauchard would suit quite well instead of an axe.
  23. Replies
    294
    Views
    57,796

    Excellent to see that something from 1850 still...

    Excellent to see that something from 1850 still has a place in modern RobotWars :) :)

    I'm still experimenting with bigger diameter drive wheel and longer arms for more thwacking and also the...
  24. Replies
    294
    Views
    57,796

    What about something like a Whitworth Quick...

    What about something like a Whitworth Quick Return Mechanism ?
  25. Thread: Melty Brain

    by adamclark
    Replies
    7
    Views
    3,947

    Are you also running the Orangutan B-328 and...

    Are you also running the Orangutan B-328 and ADXL193?
Results 1 to 25 of 119
Page 1 of 5 1 2 3 4