Search:

Type: Posts; User: team death

Page 1 of 9 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    144
    Views
    46,382

    All that driving Lucy-shows dedication, don't you...

    All that driving Lucy-shows dedication, don't you just hate it when you get diverted at night especially
    and you can't find your bearings and the Sat Nav just wants to take you back to the start of...
  2. Replies
    7
    Views
    1,595

    Here's a link to footage of the Featherweight...

    Here's a link to footage of the Featherweight championships 2019
    https://www.youtube.com/watch?v=BUf6niLnp-g
  3. Replies
    12
    Views
    4,459

    You could probably straighten that shaft with a...

    You could probably straighten that shaft with a panel pin hammer and the flat anvil bit on your vice

    but is does require a steady hand
  4. Most Roboteers have been there Greg, if your not...

    Most Roboteers have been there Greg, if your not having fun and losing to Robots you know you should beat
    it is so frustrating, you have come a long way from Bath -my advice is keep going, I tend to...
  5. Replies
    83
    Views
    17,127

    Sounds like a major Project Sean, looking forward...

    Sounds like a major Project Sean, looking forward to see what you come up with.
  6. Replies
    144
    Views
    46,382

    I'm pretty sure I could handle the motors...

    I'm pretty sure I could handle the motors conversion part but the programming of an ECU looks quite daunting for a novice , on a scale of one to ten , how hard is that programming ? .:roll:
  7. Replies
    4
    Views
    792

    I had another chance to look at the Mean Machine...

    I had another chance to look at the Mean Machine today as two of my feathers are ready to go

    for Robodojo next week.

    I was not happy with Mean Machines performance at Robots live Grantham...
  8. Replies
    175
    Views
    30,077

    Don't give up Adam, -simply solder or get a...

    Don't give up Adam, -simply solder or get a friend to solder -A red wire 20 cm long from the removable XT link to your fuse and at the other end of the fuse solder a 20 cm length of red wire then...
  9. Replies
    4
    Views
    792

    Thank's Mark and Lucy-I feel if I added a dust...

    Thank's Mark and Lucy-I feel if I added a dust pan it would only help with sweeping up my own Robot bits as they were broken off
    -those flippers are so powerful that the 3 mm steel teeth were bent...
  10. Replies
    4
    Views
    792

    The Mean Machine Revamp

    Following Robots Live Grantham 2019 I have decided that The Mean Machine needs a more effective
    weapon system.
    Originally The Mean Machine was built to take part in Robot Wars and hence the...
  11. Replies
    144
    Views
    46,382

    I'm looking forward to seeing what speed the...

    I'm looking forward to seeing what speed the scythe operates at with that 15.7 ratio.
    Those cim motors are not renowned for their speed but you could always over volt them
    for a bit more speed and...
  12. Thank's James Yes it's just arrived and your'e...

    Thank's James

    Yes it's just arrived and your'e right 3 pm and 10 am respectively.
  13. Grantham Tech check and arrival times ?

    Anyone know the arrival time and tech check time for Grantham? I registered a while ago

    but haven't heard anything, I know the show starts at 6 pm and finishes at ten which seems

    a little later...
  14. Replies
    144
    Views
    46,382

    I don't have a axe weapon but I do have some...

    I don't have a axe weapon but I do have some knowledge of cim motors and ratios.

    You would never be able to self right with such a ratio of 3:1, I would use a minimum

    of 8:1 and you will be...
  15. Replies
    7
    Views
    664

    If your wheels are plastic you will have to bolt...

    If your wheels are plastic you will have to bolt the sprocket on and you will need to be very accurate because any

    up and down movement due to misalignment or side ways wobble will cause the...
  16. Replies
    7
    Views
    664

    Where possible you should use a single axle for...

    Where possible you should use a single axle for strength and even on my feathers I don't go less a 25mm

    axle for the simple reason if you get flipped 6 feet in the air-your wheels and thus the...
  17. Replies
    144
    Views
    46,382

    In that case you are probably correct, I had two...

    In that case you are probably correct, I had two of those blow on my featherweight drive

    they seemed fine when not under load but they are poor performers compared to the 60 ESC.

    You might be...
  18. Replies
    144
    Views
    46,382

    I use the same ESC in my Heavyweight so I would...

    I use the same ESC in my Heavyweight so I would disagree that it's not suitable for a middleweight.

    Your probably not even 60 kg compared to my 110 so it must be something else.

    I would look...
  19. Replies
    144
    Views
    46,382

    Hi Lucy I think the 10 mm driveshaft are far too...

    Hi Lucy
    I think the 10 mm driveshaft are far too lightweight in a middleweight especially when your in the arena
    against heavyweights, I use 22 mm over 6 inch length in Mean Machine and seriously...
  20. Replies
    5
    Views
    689

    Hi Will You might want to check to see if Tony...

    Hi Will
    You might want to check to see if Tony smith still has Rusty for sale, it was formally known as ceros and
    appeared in series 7 of Robot Wars-it has a awesome flipper and great history....
  21. These Featherweight events have been very...

    These Featherweight events have been very popular, I think it's because of the one on one battles
    rather than all in the Arena at once.
    I'm sure Ian and Alex are on the ball but just to be sure I...
  22. I give this Robot the thumbs up for using...

    I give this Robot the thumbs up for using wheelbarrow wheels -

    quite surprised its a feather though-what does it weigh?
  23. Thread: Rex Garrod

    by team death
    Replies
    4
    Views
    7,647

    This is really sad news, Rex and his recycops was...

    This is really sad news, Rex and his recycops was the inspiration for me to get into
    Robot Wars and Robots.
    I met Reg for the filming of series two of Robot Wars and jokingly told him to get his...
  24. Replies
    49
    Views
    24,376

    The missing chapter-Mean Machine Following the...

    The missing chapter-Mean Machine
    Following the re boot of Robot wars in 2016, Team Death set about building
    yet another robot to take part in the show, Ref :Team Death New Heavyweight.

    Speaking...
  25. Replies
    33
    Views
    8,175

    You would do better to invest in an small angle...

    You would do better to invest in an small angle grinder if you are cutting

    metal out and a variety of blades for slitting/grinding.

    The thing about alluminium is that because its so soft , five...
Results 1 to 25 of 207
Page 1 of 9 1 2 3 4