Léim - Beetleweight Spring Flipper Build Diary

So I've decided that I want to have another robot that can be brought to the UK events by plane, and so, in between working on Barróg, I'm gonna try a Beetleweight design, as they seem to be picking up steam in the past few years, and ants are a little too finicky for me. The robot is called Léim, pronounced like the word "lame", and I decided on this name for two reasons. One, léim is the Irish word for "jump", which I think fits a flipper, and two, I can introduce the design by saying "I'm Eoin, and my robot is lame".

Far from going with a simple design for a first build, I've decided to make a spring powered flipper, which might be a first for UK BW's, I'm not sure. From what I've gathered, BW flippers are either motor powered fast lifters, or teeny tiny pneumatics flippers. Hopefully, a spring can give me more of a hop than motors, and more flips than pneumatics. The spring is wound back by a high torque servo using a choo-choo mechanism which allows a pull back and release function from a single rotation. At full tension, the springs exert 4kg of force, so that should be enough to hopefully get a little airtime from opponents.

As for other parts, I'm using 5mm, 10mm and 20mm HDPE for the chassis and weapon, and a 80 X 100 X 1.8mm piece of titanium for the front scoop, which should stand up to most threats. Two 2S 65C 550mAh batteries wired in series will provide power over a 4S battery for more even spacing of weight and being lighter in general. Vex 29's will be used for ESC's (not included in CAD) and modified to take the amps needed. Finally, 12V 500rpm Pololu motors will be used for the drive; I know 1000rpm are standard, but I found myself overshooting a lot with my feather, and will go for more power in drive as opposed to speed. Besides, in my eyes a slow well controlled robot should beat a quick poorly driven bot any day.

At the moment, the bot is predicted to weigh 1.2kg without bolts and wiring, so hopefully no last minute hole drilling will be involved this time round. I'm hoping to have the bot done before summers end, and get to at least one BW event in 2018, either a Beetle Brawl or the Euro Champs.

https://i.imgur.com/W8POA1Y.png

https://i.imgur.com/qwNC5Fg.png
A view of the bot with the weapon both loaded and fired.

https://i.imgur.com/wK0k2lW.png
A rough guide of where I'm planning to put all of the internals.
https://i.imgur.com/I4OvB2L.png
A more detailed look at the choo-choo mechanism.

Batteries (Turnigy nano-tech 550mAh 2S 65C Lipo Pack X 2): https://hobbyking.com/en_us/turnigy-...___store=en_us

ESC's (Vex 29 Type Motor Controller X 2): https://www.rapidonline.com/vex-29-t...roller-70-6329

Servo (HK-752MG Coreless Digital MG/BB Servo 6.3kg / 0.11sec /28g): https://www.rapidonline.com/vex-29-t...roller-70-6329

Motors (Pololu 12V 20.4:1/500RPM Metal Gearmotor): https://www.pololu.com/product/3203

Looks neat, don't think I've seen a spring loaded flipper in the BW category before.

Cheers man. The machine originally started as an attempt to make a DÃ*otóir Beetleweight, but after some thought and advice from others, the machine turned into its own thing. Still though, if I build it, It'd be pretty neat to grab some of that iconic fur and "dress up" the machine for exhibitions at Irish events such as Robots of Destruction Dublin :)

No guarantee yet as to how effective the springs will actually be. First priority is to get a test setup for the flipper working.

This looks really great - nice distinctive shape to it. I've always liked the idea of spring powered flippers, and felt that they're very underused.

If I were to nit-pick on the design itself, perhaps make the sides of the front scoop flush with the side panels? In other words, keep the pointed design, but slightly change the angle/length of the sides so that the front face is the same width as the scoop? If that makes sense? I can imagine a horizontal spinner catching the sides/edges of the scoop and tearing it up. Of course this depends on your weight allowance. Other than that though I really like it!

Also thank you so much for posting the name of this mechanism you are using! For so long I've wanted to know how a spring powered weapon could work. Am now watching videos and reading posts about this - it's super satisfying to finally understand it, even if it does have a goofy name! :lol: Kinda surprised I didn't find this sooner.

Extending the sides to fit the scoop could be done, though weight is always a factor. The arm is the way it is to actually have enough length so that it can be pulled back, essentially the entire bot was designed around it. At the moment, all the angles make a perfect octagon, the sides could be brought out, though it would need two extra wall pieces to go next to the bracket. Might have a solution to that, though I'll announce that later.

I had wanted to build a spring flipper for a while now, but it was Tantrum from Battlebots that gave me the missing key. I saw their announcement post, saw the words "choo choo spring flipper", did some digging, and so the beetle was conceived. Sometimes it's really that simple!

Parts have started to come in for the beetle, all but the servo, motors, and the HDPE. Nothing construction-wise to report on but rather this post is mostly a warning for something I've discovered about the batteries I've bought. The 4S 550mAh batteries I've bought are great specs wise, but they do have one fatal flaw: there is no main power output, and the balance leads seem to follow a different standard then the average. These batteries use a connector type called JST-XHR, while the normal standard for balance leads is JST-XH, and the two are NOT compatible with each other, differences seen in pics shown below.

https://i.imgur.com/IutuVFW.jpg

https://i.imgur.com/USEJFoN.jpg
Pictures illustrating the differences between the two types of connectors

To solve this, I've ordered two JST-XH male connectors off ebay, and will replace them with what is on at the moment. I've also ordered an adapter online that you can plug two 2S 3-pin balance leads in one end and have a 4S 5-pin balance output as well as a main power output on the other end. Special thanks as well to roboteer Tashic for his handy battery wiring guide for getting the same result without having to buy an adapter.

https://i.imgur.com/BjOQRqd.png
Tashic's handy guide for wiring in series

The one bit of construction I did manage ended in failure unfortunately. I spent close to an hour laying out the guidelines for cutting out the flipper, only for blanking out and drilling a hole too far left and going right through one of the support arms. Time to start from scratch again I guess...

https://i.imgur.com/tsyr0nj.jpg
Measure twice, cut once folks

Alright so quick question regarding servos. I've modified the servo I'm using to turn 360 degrees. I've done this by putting 2 x 2.2k resistors in place of where a petentiometer should go, so that upon recieving a signal, it never hits a limit telling it to stop, and so will keep turning until the transmitter gives it a new command. I've also removed a stopping pin on one of the drive gears of the servo, so with both of these changes, it essentially functions like a motor/ESC combo.

https://i.imgur.com/bLLzTsX.jpg
A picture of the modified servo board

I have however run into a problem. When everything has been bound, the servos default state seems to be to rotate clockwise slowly. After monitoring the signals given by my transmitter, it seems that it stops turning when in the position of -12, but I can only modify my trims to +10 and -10, so even at max trim setting, it keeps turning, albeit slower. My question is if anyone knows if there is any way on the DEVO 7E transmitter to extend the trims to further then what the physical switches allow, and to increase the dead zones on the transmitter so that it's not quite as sensitive in the centre. If anyone has any other suggestions then I would be welcome to hear those as well.

I am not sure how to use the transmitter. But you could change one of the resistor values slightly to get it a bit nearer center.
Worth double checking you have it wired up correctly as well (I can't really see from the picture)

I'm wondering exactly how I can change one of the resistor values slightly, I assume you mean to swap one of them out with another resistor? If so, then that may be hard for me as there is nowhere nearby for me to get resistors from. I'm pretty sure the wiring is alright, but I'll re-do it again just to be sure.

Another discovery I made by the way was that when I used the OrangeRx receiver from my FW, the central point was at the -12 position on the transmitter, while on an identical receiver I purchased for my BW, it was at -17. For the record, I'm using a Devo 7E with Deviation software if that can help anyone to figure out how to modify dead zones on the transmitter, though it seems that there is variation with the receivers in this case.

No idea whats going on with the different trim values with the same/different Rx's, but you could check something with the resistors. Did you measure their actual values before fitting them? Like all components they have a tolerance and although I doubt it, you may have one near the bottom end of the range and one near the top. Measuring them with a multimeter would rule this out, but be sure to un-solder one end of each resistor before measuring it. Long shot, but worth a check.

I've monitored a few for their resist value with a multimeter and they seem to be the same, but swapping a few in and out shouldn't hurt. I'll do that soon and keep this post updated.

In reply to your post.

Quote:

---

I assume you mean to swap one of them out with another resistor?

---

That is what I meant.

My thought with this, is that the servo is centered around a voltage that is not exactly half way between the rails. This test will check that you are using the right resistors:

1) set your trim to 0 on your transmitter
2) solder the potentiometer back onto the servo (don't attach it mechanically to the servo)
3) turn everything on
4) Your servo will probably move, so adjust the potentiometer until the servo stops moving. This should now operate like we want it to (in continuous mode), so move the sticks on the transmitter to make sure.
5) use a multimeter to measure the voltage on each side of the potentiometer*1.
6) the ratio of these voltages should be the ratio of the resistors you use*2.

Let me know if I haven't explained something well enough.

footnotes:
*1) If you are not sure how the potentiometer is wired, measure the voltage across each pair of legs (ie measure pin 1 to 2, 2 to 3, 3 to 1). The two smaller voltages should add up to the larger one (ignore any minus signs). Its the two smaller voltages we care about.
*2) For example, if the voltages you read are 2.4V and 2.6V, then the ratio will be 2.4/2.6. You have a 2.2k resistor, so we can calculate what the other resistor should be: 2.2k * 2.4/2.6 ~= 2k. The larger resistor should go across the place you measured the larger of the two voltages.

Ah, I see, very clever! Cheers for the explanation. I believe that this also means that in a pinch, just having the potentiometer soldered to the servo but not attached to the main drive gear can act as a resistor combo, though is probably more fragile then the resistors and needs extra care. Thanks again!

Yes, you can use the potentiometer if you have to. The potentiometer can be imagined as two resistors, which change value depending on how much you turn it.
I think if you glue the potentiometer it in place so it can't turn it should work, but that doesn't seem quite as robust.

This is how I used to modify servos for 360° rotation too. Take the output gear off, cut the tab and bore out the underside with a drill to remove the slot that goes over the potentiometer, turn the pot manually to centre the servo from the transmitter and dollop some superglue on the pot to stop it from moving. Never had an issue in many years.

Time for more updates! Léim has progressed far more quickly than I'm used to with my other builds, and should reach its goal of being ready before the end of August, in spite of me being completely removed from my workspace for these first two weeks of the month.

While new connectors arrived for the batteries, they used a different pin system as well, and after trying for a week to change the pins around, I just couldn't do it. So instead, I've cannibalized some balance connectors from my antweight batteries and soldered them on to the new beetleweight batteries. It means that work on my antweights has become a little trickier due to not being able to charge the batteries, but at least I now have a power source that's lightweight, and whose weight is evenly distributed.

https://i.imgur.com/gctgxcn.jpg
The new battery configuration

https://i.imgur.com/1kvp9Y2.jpg
A moment of silence for a fallen comrade

Thanks to the batteries now being finished, I was able to test out all of the electronics together. To my pleasant surprise, everything seems to be working first try! The wheels haven't been completely secured yet on account of not having the correct Alan key, but even with this handicap the machine controls beautifully, far better than anything I've ever built. I'm starting to feel like the 500RPM motors will pay themselves off in spades in combat, so long as arena hazards exist in any arena I fight in.

https://i.imgur.com/ZD99URM.jpg
All of the electronics laid out

Drive Test:
https://www.youtube.com/watch?v=OeYnDEH4TDo

As well as all of this, a huge amount of the work on the body has been cut, with only the top plates and flipper arm left to prepare, as well as hollowing out the right flipper bracket. I've decided to change the armour on the front from 10mm to 15mm HDPE, which should hopefully do the job against the new wave of horizontals in beetleweights, especially since that'll be where the batteries are. The hollowing out job I've done on the flipper bracket is something I'm particularly proud of. All that's left is to assemble the parts together with barrel nuts, and thanks to the angled cuts on the wall pieces, the machine should be particularly effective at taking inward blows.

https://i.imgur.com/Xxgti4u.jpg
A shot of the outer walls with headphones for scale

https://i.imgur.com/WI6Lrd2.jpg
The work done on one of the flipper brackets that will allow the machine to stay underweight

I ended up bringing up my electronics with me to this island holiday to be certain the servo works once and for all with the clipped potentiometer, but unfortunately I ended up leaving the receiver at home, so that was a bust! Everything is place, I just need to confirm that it works. I've also sent in the titanium to a metal cutting crowd in Galway, and while I'm certain that all the pieces will be cut to my specifications, I'm always a little anxious when the timeframe is this thin. Still, the machine has come along very well so far, and it's always great to see my drawings coming to life in front of me. The only things still left on the checklist are to check if the flipper mechanism actually works, and the paintjob.

https://i.imgur.com/s1kOszv.jpg
A shot to give a rough idea of where everything will be, barring the left side battery

https://i.imgur.com/BUHT0ET.jpg
The point at which I've had to leave the build. At this point, I'd say it's roughly 60 to 70% done

This is looking great :) - Can't wait to see the weapon!

Well it's been a while since I've updated this build log, but now that it's aired, I can say a bunch of stuff about the build I wouldn't have said usually. So as most of you are aware, Léim was actually being built for Bugglebots, and its performance in the competition was... mixed. But before going into that I still have some catching up to do in the building perspective.

So in between all of the work I was doing on getting Barróg ready for KOB UK/Insomnia 63, I still had far more to do with Léim, so much so that I was working on it during the event to show the TO's, who were competing at KOB themselves, proof of my weapon's functionality. Fortunately, I was able to do quite a lot of work in the little over a week I had between coming back from a holiday and travelling to Birmingham. Most importantly, I was able to rig up my weapon system. I originally bought a metal servo head for the linkage, but unfortunately its teeth didn't mesh with the servo head, so I ended up using the plastic one instead. After a broken first attempt and quite a bit more money than what it probably should have been, my titanium scoop and linkage arms arrived, and I was actually quite happy with these! I tested flicking the chassis by hand with the springs at their max tension, and the bot actually self-righted, which I thought to be a good sign as well.

https://i.imgur.com/aTPfbZa.jpg
The flipper mechanism mostly set up with the servo in place. It needed to be recessed, and doing that without a mill was quite the challenge!

https://i.imgur.com/DF50t3z.jpg
The two spring setup in place. In theory, this would be able to lift 4kg at the tip, provided I could wind it down to that point.

After getting back from KOB UK, it was simply a matter of getting everything wired in place, and getting the final pieces prepared. Unfortunately, one of these pieces included the 5mm top plates, and I seemed to misplace all the 5mm plastic I had at Insomnia. Fortunately, I put out a call for help and Nicholas Cole (Builder of Sir-Lance-A-Frog) offered to cut the pieces himself, and just give them to me at the competition. Massive thanks to him! With that in mind, and as time was running short, I cut placeholder pieces out of 1mm polycarbonate, and opted to paint them along with the front plate, and just bolt the painted pieces on top of the HDPE.

https://www.youtube.com/watch?v=bEoMR0GrnIk
A drive and weapons test shortly before leaving for Bristol.

https://i.imgur.com/g2fw6Qr.jpg
The machine test-weighed. I knew the HDPE would add something, but my weight at this point allowed it.

https://i.imgur.com/WpXS3sK.jpg
Painting the top plates and front piece in Dublin, essentially mid-travel. Was nervous it wouldn't be dried before leaving for the plane!

Unfortunately, things weren't all great. The main thing I discovered during testing was that the servo would stall when trying to wind both springs down to their loaded position, evidently I had miscalculated somewhere along my planning. So to even have a working weapon at all, I had to downgrade to one spring, with a max force (in theory) of 2kg. Not really a flipper at this point, but it was all I could do in the short time, and at least I could show off the mechanism as a proof of concept. As well as that, in my rush to paint the top panels, I ended up painting the wrong side of one of them! As a quick solution, someone in the Bugglebots crew suggested using the dark-green spray paint used for the arena, so that's why the top is in such a different shade of green!

https://i.imgur.com/INsxQRz.jpg
The choo-choo with no tension...

https://i.imgur.com/5lrGn2J.jpg
And the choo-choo at max tension.

https://i.imgur.com/EuNwCv0.jpg
The machine, nearly ready for battle!

With that, all that was left to do was to transfer the wholes from the polycarb plates to the HDPE panels, get through tech-check and weighing, and I was ready to go! With that, I did my intros and interviews (my teams usual green shirt caused some headaches for the green screen crew!) and prepared for the fights ahead...

FIGHT 1: ROUND 1

I was slotted in for heat 4, and my first opponent was Claws 2 from Team Luna-Tic. I had faced the team before in my second Insomnia melee, and I knew how determined this family team was, as well as how well driven these machines were. With the chance of flipping them being questionable at best, I instead hoped the "flipper" would lift them slightly off the ground, enough to gain a control advantage in what I was sure would be a pushing game, similar to US spring flipper BW Butterfly Effect. I loaded into the arena and prepared to fight my first beetle battle.

https://www.youtube.com/watch?v=EzJvcrFoddw (Skip to 14:14)

Some observations from this fight:

• One weird thing about the drive on Léim was for some reason braking was enabled on one of the Vex 29's and disabled on the other. This meant whenever I'd let go of the stick Léim would essentially do a 180. As I only really discovered that in this fight, I had to adapt quickly, and so much of the start of the fight was dedicated to learning how to drive the bloody thing.
• Claws 2's weapon was really the perfect shape for grabbing Léim, but there weren't too many times I was properly "grabbed" as it were. Still though, they definitely gave Felicity the control advantage, and as I couldn't win the wedge game I had to focus on getting around Claws 2 instead.
• During the pin on Claws 2 about a minute in I was desperately activating the flipping mechanism in the hopes it could lift something. Unfortunately, Claws 2 didn't move a milimeter, and it was at that point I knew the flipper was a failure. Sigh...
• Despite the weapon performing poorly, I honestly felt I had the slight edge in the control game for the first two minutes of the fight, and so long as I kept the flipper loaded, the titanium frontpiece still could be a decent wedge. Shame the flipper distracted from that I suppose.
• Unfortunately, in the last minute of the fight, I lose drive on one side, and I can only really limply try to agitate Claws 2 as I'm bullied around until the judges decision finally arrives (fun fact: as all round 1 fights were filmed together, this was the first judges decision of the competition).

POST-FIGHT:

I knew even before the decision was read out that I'd lost, and fair play to Chris and Felicity, that is a nicely built and controlled bot. It was certainly disappointing for me however, this was really the first bot I'd ever built which just didn't work how it should've, and I felt I had done no favour to the image of spring flippers. Once I took the bot back to the pits, I saw what caused me to lose drive in one side. One of the grub screws holding the wheel hub to the motor had come loose; I knew this was an issue with Banebots hubs beforehand, but I didn't have the time or the tools to fix it before the competition, something I definitely paid for. I was still in the competition however, and there were still things I wanted to prove with Léim, one way or another. I wanted to see how far I could push the bot with sheer willpower alone.

https://i.imgur.com/4MAc3oW.mp4
The grub screw, barely holding on in this instance it seems.

FIGHT 2: REDEMPTION MELEE

My redemption melee battle put me against The Berg, a nasty drum spinner who lost their first fight due to unfortunate link placement, and Apex BW, a nasty overhead bar spinner which suffered numerous failures in its opening fight. As well as being built as a flipper, Léim was designed to tank hits, that front had 1.8mm titanium, and the walls at the front were 15mm HDPE (for comparison, Barróg has 10mm walls, my beetle is thicker than my feather). Both of these bots would be great tests for Léim's durability, and I was especially glad to finally face an Apex bot after missing out in my third Insomnia qualifying match only a few weeks ago. With these goals in mind, I loaded up, and prepared to fight to survive.

https://www.youtube.com/watch?v=EzJvcrFoddw (Skip to 23:31)

Some observations from this fight:

• I got some nice sparks from The Berg in those opening hits, and I seemed to tank many of Apex's hits with no problems. All was going well so far!
• It seems that my wires inside the machine kept getting caught in the wheels, and so while I only properly started losing wheels in the final minute, I had mobility problems throughout the fight.
• Fortunately these problems subsided long enough for me to get a well-timed charge on The Berg, and somehow managed to pit my biggest threat at that moment while staying out of it myself. Pretty happy about myself for that one.
• At this point Apex was having issues again, and both of us were now struggling to move towards the other. I had more movement, but only barely, and the multiple hits seemed to knock something in the pentiometer loose, causing it to flip uncontrollably.
• At one point, I lay off Apex completely to allow him to spin up. I came in here to prove I could take the hits, and by god, I wanted to see that happen, one way or the other. Unfortunately, Apex just couldn't shake its curse, and so I was left to limply charge at him once more.
• Nearing the end, I was actually feeling fairly confident I could win via a judges decision, due to my control earlier in the fight and the way I tanked earlier hits. Unfortunately, my re-tightening of my wheels just didn't hold, and so they gradually gave way, knocking me out with only seconds left. So close and yet so far...

POST-FIGHT:

So I was out of the main competition without a single win. Certainly a disappointment after a stellar run with Barróg only a few weeks prior, but it wasn't all bad. Léim gave me a chance to prove my building talents, and no matter its results, I'm still proud I could get it, as my first beetle, up and running for a tight deadline when so many other builders couldn't make it. The bot took hits well, and while yes it did lose functionality in several places, it certainly lasted longer than some of the other competitors, so I could take credit for that. It was also just fun being at the event, everyone was lovely and the fights, pits, and competitors were all brilliant for me to witness in the flesh, even more so as I was still so new to this whole thing.

https://i.imgur.com/Pa6KKKy.mp4
A quick sweep of the bot post-Berg and Apex. Some small nicks here and there, but otherwise, it's 100% structure-wise.

I'm still going to hold off on some more thoughts, as this actually wasn't my last fight at Bugglebots. There is still more to come from Léim, and I'll wait to update you all on those, as well as some concluding thoughts, once the entire series is out. Cheers for reading, the rest of the show will be a hoot!

I really liked Léim on Bugglebots; I've always thought there must be a way to make an effective spring flipper, especially in the beetle class where I guess there's no suitable option for pneumatics, so I was really interested to see how you'd got it to work. It is a shame you didn't quite crack it this time but kudos for having a go. Given you're working with a pretty novel concept it's good going to make something that kinda does the right moves, even if the power isn't there yet. I'll be interested to see how you develop the concept - it's got a lot of potential, so I hope you'll stick with the idea!

Cheers for the support. I have many improvements planned for the next version of the bot: four-wheeled drive, brushless, an entirely new shape, and a far more powerful, hopefully actually viable flipper. Will update this post once I've happy with what I can show off.

I hope you're going to keep at least one screw the same so you can say it's still the same robot. :mrgreen:

Look forward to seeing V2!

Now that the rest of the Bugglebots specials I was in have come out, I can finally finish off this event report.

FIGHT 3: DUNG BEETLE MELEE


So even though I was out of the main competition, I was by no means done fighting. My next fight was the Dung Beetle Melee, where all ten competitors without a win in the main competition competed for a "best of the worst" style title. The only notable thing to point out before the fight was that as the melee was filmed early on the final day of filming, the team behind The Berg couldn't make it to the interview beforehand, so I offered to impersonate Charlie in his absence (minus the whole getting dragged out by Tim thing). I've gotten a lot of mileage out of other shirts this event!

https://www.youtube.com/watch?v=iOKy_QdHOAI

Some observations from this fight:

• Just shoved some stuff around really before getting knocked upside down by The Berg, going out at 8th. Not really a lot to add here, just a sucker for consistent formatting.

POST-FIGHT:

The good news was that the machine could still drive, but the bad news is that the hit from The Berg actually shattered the servo arm that wound the flipper mechanism down, so what little use it had was now gone. Fun fight at least to watch, so I couldn't complain!



So thanks to there being a Rest of the World special being hosted as well, I was given one more fight to compete in, and was drawn up against Zero Gravitas. Given how Team International had done so well up until this point, I was nervous going into the fight as now a loss would be disappointing for people other than me. Since the spring flipper mechanism was bust I used a bolt to hold the flipper blade down, and as such so long as I could drive around ZG the 500RPM wheels should allow me to push him. The rest of my strategy was covered in the pre-fight interview, so all that was left to do was to hope for a win in a pushing match.

https://www.youtube.com/watch?v=xFnOYiXCYuI (Skip to 15:45)

Some observations from this fight:

• Zero Gravitas decided to wear some red fur on the top of its jaw for this fight, a knowing nod to fellow Irish robot DÃ*otóir, which I thought was cute.
• I was still having issues with my wires sometimes getting caught in the wheels, but overall I'd say we were even on control. For once the torque-ier motors actually worked to my advantage: ZG could never push me even with a clamp, but every time I got him from the sides or back I could push no problem.
• A minute in and I get a nice push that nearly pits ZG. A while later and pit shenanigans ensue, with each looking for the right twist that would get the other in the pit. Unfortunately I am unsuccessful, and after a while later I lose drive on one side again.
• Once I lose drive, I know I've lost my only advantage, so by backup strategy was to shuffle near the pit in the hopes that I could get a cheeky move in that would pit ZG. Fortunately I get a chance, and some iffy driving from ZG leaves them teetering on the edge.
• Fortunately for me, all of my time driving on one wheel had gotten me pretty well practiced in driving like that, and with some skillful shuffling I was able to pit my opponent, scoring my first beetle win and a clean sweep for Team International!

POST-FIGHT:

So I was pretty happy with that last fight; I'd say the roughly 9 minutes of roasting Léim got throughout the competition was at least offset by some decent driving at the end there. Unfortunately the damage to the drive was a little worse than previously, as one of my motors had actually seized up, as well as one of the ESC's no longer working. It was worth it though, and the fight seems to have gone down well with people, can't complain when you end an event on your highest note!

POST-EVENT THOUGHTS

• Due to the damage sustained, Léim is now retired. I am considering rebuilding the bot at some time down the line (replace the motors, ESC's), and putting in a beefier servo to at least have a spring system that can at least lift. If I did that I'd even be willing to sell it outright, though I do have other priorities at the moment, so that's on the back burner.
• I severely underestimated the energy needed to make a viable spring mechanism. The next iteration of the machine will be using a low RPM high torque motor that would put the previous servo to shame.
• The Banebots hubs consistently failed me over and over. I know of some teams who've modified them to be more reliable, but my next design will use wheels that bypass the hubs entirely.
• The thing I'm most proud of with Léim was how well built it was structurally. Any damage it sustained was shrugged off completely, and I reckon the machine could take hits from some of the nastiest spinners in the country over and over and keep going the full three minutes if I mounted the electronics and wheels right.
• The success of Maximum Ogredrive has made me wary of beetle saws in the future, and the next machine I build will aim to bypass them in a creative manner.

Overall a very fun event, and everyone there deserves praise. Special thanks to Mark for being pit buddies (congrats on winning btw!), Alex Mordue for being so friendly and donating 4 brushless ESC's to me, Jeroen and Cosmin for sharing a house during filming and the lifts towards the event, Robert for sharing some of his designs with me, all of the other roboteers, and all of the event organizers for putting on such an incredible event. If there is a second season of Bugglebots, I would be absolutely delighted to return, hopefully this time with a machine that can actually live up to the hype!

Quote:

---

Originally Posted by Shooty

Not really a lot to add here, just a sucker for consistent formatting.

---

Damn right!

Great write up, and congrats on the last fight. I was properly on the edge of my seat while Léim was single-wheel-jiving over to ZG. :mrgreen: Looking forward to seeing what you take to the next Bugglebots!

So with Bugglebots coming back and after the disappointing performance of Léim last time round, I've began a new spring flipper build with the intention of fixing all of the mistakes the old model had. I'm calling the new build Léim Thart, and the goal of the build is to make a viable spring BW flipper, same as last time but hopefully without the same failings (pronounced "lame heart", and means "jump around" in Irish. Also now you can listen to this while reading and suffer as I did as a kid: https://www.youtube.com/watch?v=bJ_vU_RAaZY

https://i.imgur.com/HMKk0lO.png

https://i.imgur.com/wvAth3m.png
An overview of the CAD. As you can see the design has gone through a complete overhaul.

the previous design unfortunately didn't live up to my expectations, and for this machine I had two goals driving the entire project: to have a stronger, more reliable, four-wheeled drive, and to optimize the flipping mechanism to get as much energy as possible from the springs into the flipper. As such, I've forgone the old DÃ*otóir-inspired design for a design inspired by US Beetleweight Butterfly Effect's winding mechanism, and American flippers such as Bronco or Sub-Zero, which aim to reduce the distance between the rams and the flipping blade. I've scrapped the choo-choo mechanism for a more traditional snail cam mechanism, and have swapped over to using two compression springs mounted on shock absorbers to allow them to hinge. The trick for me here was to design the flipper in a way where a) the springs were as far forward as possible to the start of the flipper for maximum energy output and b) the cam was as far forward as possible so that I could get as much useable torque out of the motor as possible after all other losses (size of the cam, increased forces by being behind the springs etc.).

https://i.imgur.com/bLyjdXm.png

https://i.imgur.com/Gat3ccb.png

Shots of the flipper mechanism in the wound and fired position.

The motor I'm currently using is a Servocity 34RPM Econ Gear Motor (https://www.servocity.com/34-rpm-econ-gear-motor), which has an output of 110.20 kgf/cm, though I may upgrade to the 19RPM model in the future for an absurd +180 kgf/cm. For the mechanism I'm currently using two Flexo Springs 133414 (http://www.flexosprings.com/stock-sp...springs/133414), with a rate of 10.51 N/mm, compressed down to 15mm. I've taken most of my parts for the motor mech from Brandon Zalinsky's US Beetle Butterfly Effect, with the exception of using a snail cam winding method instead of his choo-choo inspired method.

For the drive, I was impressed by how much power WeeWoo had at Bugglebots, and after getting some brushless ESC's from Alex Mordue there, I decided to go brushless for Léim Thart. The drive will use 3D printed wheels with hydraulic hosing for rubber grip, and I will be replacing the Banebots hubs with press-fit wheels instead protected by 5mm HDPE. I'm using DYS BE1806 2300KV motors (https://www.banggood.com/DYS-BE1806-...r_warehouse=CN), combined with the Rotalin Planetary Gear Motor's gearbox (https://www.ebay.com/itm/Rotalin-Pla...1-87ca813ef861), with belt drive to drive the front wheels. As well as all of this, the new design will use interchangeable titanium flipper blades, as well as a D2 inspired hinged wedge for the rear for horizontals, though the thickness is entirely down to what I can source.

Given how irritated I was at the performance of the bot last year, I decided to segment the build to get all of the new parts of the build working before combining. As such, I set myself the challenge to not apply for Bugglebots S2 until I had a) a driveable base for the 4WD brushless drive, and b) a working spring mech that could send the old Léim chassis airborne. The next few posts here will be my build logs for how I got both working, to be written in the coming days. Know now though that I have accomplished both, and have now submitted in my application for Bugglebots 2019. I look forward to publishing all I've done so far.

https://i.imgur.com/k4H6xfy.jpg
The old Léim chassis along with my flipper and drive base, to be explained in the upcoming posts.

Looking great! I like the symbolism of New Léim having to defeat Old Léim before taking its place... :mrgreen:

Oh and I guess thanks for the video :?

That's a really neat design - looking forward to future posts.
Also you need to play this song when your robot enters the arena!

Well, this post may be a smidgen late (ahem), but I’m finally at a point where Season 2 has aired, I have enough time to do a large write-up, and most importantly, I can be arsed to do this. So before going into the event, let’s take a quick look at how Léim Thart came together.

https://i.imgur.com/PSusyrK.jpg
The Léim Thart chassis nearing completion.

For the drive setup, I built a mock platform which was meant to replicate the drive of the final machine on a one to one scale. Getting the DYS1906 motors to work with the 22mm planetaries wasn’t easy, but a handy guide done by Cosmin Gorgovan on the Beetleweight Robot Combat page got me through, and the end result was very compact. Flashing the ESC’s proved a bit trickier, requiring an Arduino to program as well as some custom firmware to get everything working correctly, but after a bit of tweaking I had a working drive system going!

https://i.imgur.com/DMrfP1z.jpg
The new wheels and brushless drive. Note the mould for cutting tires in the background.

This project also marked the first time I could use a 3D printer (in my case a Wanhao i3 Duplicator Plus), and this would prove very useful in the creation of my new wheels. The wheels on one end press-fitted onto the gearbox shaft, and the other wheel ran on a bearing at the front of the machine. I could even use 3D printing to make a guide that allowed me to get perfect cuts out of a silicone hose I was using for tires (thanks for the inspiration RobertK!). I used rubber bands to transmit drive in the short term in place of the proper PU belts, and when run on 4S the speed and control of this bot was a substantial improvement compared to the original Léim!

https://i.imgur.com/1uMUWmB.jpg
The drive platform I used for testing.

https://www.youtube.com/watch?v=3I1eaa59Vgc

Having good drive was just one piece of the puzzle however, as if I wanted to have a good bot, I needed a weapon that would actually function this time. This involved 3D printed shock absorbers that required multiple revisions to take the forces demanded of the springs, and though frustrating to redesign and reprint over and over again, the fifth revision would ultimately prove successful.

https://i.imgur.com/vY0WELW.jpg
The testing platform for the spring flipper.

https://i.imgur.com/1bkGnJU.jpg

https://i.imgur.com/03b0qQ7.jpg
Some more views of the mechanism.

Cutting plastics comprised a lot of the challenge of this mechanism, most notably the snail cam that drove the mechanism (thanks to Mark Joerger for the advice for improvements, and Shakey for the milled cam later on). After a few revisions though I finally had everything assembled and could test it on the old Léim chassis. While not a massive flip, it *technically* went airborne, and as those were the less powerful springs I had in the mechanism, I was confident I could improve it more in the future.

https://i.imgur.com/TSsTAG8.jpg
Mid-way through cutting the weapon cam. This was all painstakingly done by hand, and while the finish was excellent, I outsourced the final product just to be even more safe.

https://i.imgur.com/PMkf9nH.jpg
The machined finished cam next to my first attempt (I gave it two tries before outsourcing).

https://www.youtube.com/watch?v=6I66yfPh0KI

So at this point I had improved both my drive setup, and my weapon, and all that would be required now would be to combine the two setups. Seems like smooth sailing doesn’t it? Well, while everything looked good from this angle, we are merely in the eye of a storm that brought up many problems that nearly sunk the whole project.

The Weapon:

https://www.youtube.com/watch?v=NWR5AVhxAi0

The problems are two-fold. First of all, I again messed up with my understanding of springs. While I had far more power at my disposal than previously, Springs differ from the pneumatics used in similarly shaped machines in one major way: the further the travel, the less energy they have. This meant that if I didn’t have a bot touching my flipper blade, I wasn’t going to flip anything at all, and it instead became the world’s most disappointing lifter. In hindsight, I shouldn’t have used springs with such a short travel, and instead have used a flipping mechanism that brought springs from 100% tension to maybe 75% or 67% tension instead of going from 100% to 0%.

Secondly, I needed torque, and lots of it. The Servocity gearboxes promised a lot of torque, and while they (mostly) delivered it, there was one small snag. These gearboxes were a bunch of spur gears stacked on top of each other compared to the standard planetaries, and the second the motor couldn’t compress the loads demanded of it, instead of the motor stalling, it just sheared the gears at the end of the gearbox. This lead to a *lot* of testing where I had to dismantle and rebuild my entire gearbox. Fortunately, the old drive gearboxes on the original Léim had the exact replacements I needed, but this setup was still incredibly fragile, and I’d have to be extraordinarily careful not to mess the entire mechanism up.

https://i.imgur.com/0DNtxlf.jpg
Was this image taken in March, April, May, or during the event itself? Who knows, because this image is nearly identical to other images taken during this time.

Titanium:

https://i.imgur.com/jiX6tY8.jpg
Along with the digital drawing files, I also provided this guide to get the most out of the piece I had.

I was very fortunate to be able to buy a nice piece of 2mm grade 5 titanium from Mark Leigh following the event, and the size of the piece allowed me to get multiple flipper blade configurations from the piece on top of a very nice wedge to counter any deadly horizontal spinners that could show up. After the good job done on Léim’s scoop, I contacted the same local machine shop I used last time to get the pieces cut and bent, providing them plenty of detailed drawings and with months to spare for myself. What followed was one of the worst experiences I have ever had with outsourcing some work. Some highlights include:

• A delay of weeks from the original promised date, putting me under more pressure to get the build finished on time.
• Massive tapers left on each part.
• Several holes drilled in the wrong location from the drawing.
• One piece cut several centimeters shorter than what appeared on the drawing.
• A crack in the bent titanium wedge that was mentioned *nowhere* and that I only noticed in person seconds before paying for the work.

https://i.imgur.com/M5TiRze.jpg
My finished titanium wedge, with misplaced holes, and a rather noticeable crack on one side.


Weight:

https://i.imgur.com/jXXz2fc.jpg
Isn't it fun to go on a diet?

While every issue up until now would be detrimental to my bot competing, one that kept creeping up concerned the weight of the final product. I had given myself some allowances for items such as bolts and nuts, but the end product was still substantially heavier than I expected. Some major work was done to lighten the machine, including hollowing out as much of each bulkhead as was possible, switching to a lighter battery, and even scrapping the notion of running the titanium wedge entirely, and even after all of this I left for the final show uncertain that the end product would fit in underneath the weight limit of 1530g.

https://i.imgur.com/BerFLPw.jpg
Taken shortly before leaving, I was hoping to lose the last 35g with the new battery I'd get at the event itself.

While wrestling with these issues I finished up the final parts of the robot. A link holder was 3D printed which mounted to the side bulkheads, and would be re-used in both Barróg’s. The side armour was bent and fitted, which served both as armour and to give the bot a bit more character. I could also work on some full-function tests, from driving to self-righting (a little spoiler, the latter didn’t work).

https://i.imgur.com/ffNpRXW.jpg
The finished link holder, which also held the battery fuse and LED power light.

https://i.imgur.com/c1ZB8jL.jpg
The beauty shot I took of the spring flipper the night before leaving Galway.

It was only with a week to go that I had a realisation with the weapon. I knew that the springs were a little unreliable at best, but that being said, I did have a motor with a lot of torque sitting in the bot. I theorised that I could convert the spring flipper into a four-bar lifter if pressed for time, and so in a few hours, CADded up a design which I could cut out and print in a day as soon as possible. The concept not only worked, but this would also save a lot of weight, and allow me to use the titanium wedge when running it! I kept it a secret to all but the producers, packed up the rest, and left hoping that I could get everything competition-legal once I arrived.

https://i.imgur.com/d02bdV5.jpg
A top down view of the bot with the four-bar in place.

https://www.youtube.com/watch?v=zBNIeypajr0

Bugglebots 2019:

After a quick stop-off in Cambridge, I arrived in Bristol a day before the competition, and got to see the new and improved pit-space for the first time. I got myself unpacked, got friendly with my pit buddies (Felix Townsend of Rev 4 in my case), and spent the next few hours frantically trying to remove weight off my bot. I had an awful lot of help from other builders, especially Felix who grinded my Titanium blades and melted together my PU belts, bought a spare battery from Rory Charlesworth, and did a ton of cutting and countersinking of both plastic and titanium to get a finished bot together. I was staying in what I’m just gonna call the ‘Drizzle’ house (Tom, Sarah, Tim, Catherine, Charlie, and Aaron), but I actually didn’t end up leaving with them that night just so I could get the bot checked and ready to go. After a final desperate session of swiss-cheesing, the robot had *finally* made it into the legal weight limit with not a gram to spare. Phew!

https://i.imgur.com/EEEysBJ.jpg
Talk about cutting it close!

We all arrived the following morning, got ourselves ready to compete, and heard all of the draws for each heat. Ours was an interesting one with a variety of weapon designs, and while I didn’t ever believe that I could win the heat, I remained hopeful that I could at least show some improvement from my last competition.

Fight 1 VS. Unconscious 514:

My first fight was against what may have been the most unconventional design in the competition. Unconscious 514 (Shirumi Eku) was a crusher bot coming all the way from China, two things that have never been seen in the European circuit. I was fortunate that this was my first opponent, as it allowed me to show off my new spring flipper design. I knew that Unconscious had a weapon that could go through my 2mm HDPE top armour like it was nothing, but my one advantage was that it was slow to self-right, so if I could get around him, I could have enough power to flip him over, then start to control the fight while he was upside down.

https://youtu.be/e6s71P2wHGM
Fight starts at 11:02

The fight started with me getting accustomed to how Léim Thart drove in this new arena, as well as noting how Unconscious was struggling to get past the lips on the floor. I knew I couldn’t take Unconscious head-on due to him winning the ground game and the lethal potential of the weapon, so much of the fight was me just trying not to overcommit to one attack, but also to try and get behind Unconscious, which was a challenge indeed thanks to Shirumi’s excellent driving. You can actually see the flipper fire once around the 40 second mark of the fight, but the blade was just too far away.

Things were going quite well, and I managed to control the bot better and get behind him more often as the fight went on, but unfortunately one unlucky shove left me stuck in the jaws of Unconscious, with little chance of escape. I actually tried firing the flipper here, but the gears inside the lifter gearbox had exploded like usual, and I was left with no more options. Interestingly enough, the exact same thing had happened to Unconscious, but he still managed to get the KO via pitting.

The good:

• The drive is fast, grippy, and controllable. Heads and shoulders an improvement over last year!
• The flipper fired in a fight, and rewound itself without breaking.
• My battery was barely missed, so no irreparable lipo fire.

The bad:

• The weapon never landed a hit, and so I never got to show off the months of hard work that went into the weapon.
• The gearbox shredded some gears again, resulting in another disassembly and rebuild.

https://i.imgur.com/qFSdhcG.jpg
The mark left in the top armour by Unconscious 514.

Fight 2 VS. Rev 4, W I D 3 B O I:

This match put me in the heat’s redemption melee against two people who had actually helped get Léim Thart to a finished state, and both called for very different strategies to beat. The titanium wedge to take Rev 4’s (Felix Townsend) monstrous hits was an obvious move, so I dismantled the spring setup and replaced it with the experimental four-bar lifter. WIDEBOI (Alex Shakespeare, also I’m not doing the full name again) meanwhile was an excellent controlbot, and I was uncertain I could get around him, so I needed a strategy for head-on collisions. I had brought along a longer titanium arm with a bot to act as a keepaway stick, with the intention of countering forked machines such as Thunder Child, and with a bit of measuring by eye, I positioned the bolt in such a way where I could catch WIDEBOI between its toes and lift it up, shifting all the weight to my end and giving me an edge in any resulting pushing match. Speaking of weight, even with the four-bar I was still over the weight limit, so I actually had to scrap some of my top armour to even make it into the arena!

https://i.imgur.com/2LjgiMd.jpg
The re-modified robot ready to go into the arena.

https://www.youtube.com/watch?v=e6s71P2wHGM
Fight starts at 27:05

The match started cagey enough, with my priority being to keep my wedge pointed at Rev 4 for defense, though once it KO’ed itself after deflecting off the wedge I could focus on WIDEBOI head on. This was a fun matchup; the waggle-sticks on WIDEBOI could easily hook onto the top of Léim Thart, but the keepaway stick and lifter combo allowed me to push WIDEBOI around quite a bit, and when all four wheels were on the ground Léim Thart had a massive amount of speed and pushing power. After a lucky slam near the pit, I managed to go around it while WIDEBOI found itself falling in. Léim Thart had managed its goal of getting further in the competition than the previous machine, and with next to no damage I could finally take it a bit easier in preparing for the next fight!

Fight 3 VS. The Apprentice:

This match saw me against The Apprentice (Mark Smith), an overhead spinner that had a lot of energy and that, unfortunately for me, had a weapon that would hit over the titanium wedge at the back. I modified the keepaway stick in such a way where I hoped I could lift a still-spinning robot so that it would destabilise itself and give me a KO victory.

https://youtu.be/e6s71P2wHGM
Fight starts at 40:31

Starting out the fight, I noticed that The Apprentice took quite an amount of time to get up to speed, so my main priority was to stop the weapon as often as I could and to stop it from doing any significant damage to me. The HDPE armour actually stood up very well to the blows from The Apprentice that landed, and though the keepaway stick didn’t really get a chance to work properly, I was able to get some aggressive slams into my opponent. Near the end of the fight, The Apprentice seemed to be losing either grip or drive, and I was able to get a very unlikely KO on a bot that I was quite afraid of, and somehow managed to make it all the way to the heat final!

https://i.imgur.com/FS5xIUB.jpg
Fully repaired and ready to go into the heat final!

Fight 4 VS. Saw Loser:

The second day of filming started with significantly less stress than the first. My heat final matchup put me against Saw Loser (Alex Mordue), a rather poetic final opponent for the heat given that Alex was the one who gave me the brushless ESC’s last time that gave Léim Thart its new effective drive. The press-on wheels that I had been using had started to loosen quite a bit (foreshadowing), so I switched to a spare set, and was able to print a new wagglestick holder to replace the one that broke last fight thanks to Chris Danby actually having a 3D printer with him at filming. All I could hope for was to last until the pit was available, and hope to get Saw Loser in, but it was always gonna be a gamble.

https://youtu.be/e6s71P2wHGM
Fight starts at 48:24

The fight began, and things looked good; I was able to outdrive Saw Loser due to his gyro, and even managed to get it turned over. It recovered fast however, and one hit from that weapon left me stranded on my back, unable to move. Alex was a good sport and tried to right me again, but the fight was basically over from there, and so the win for Saw Loser was achieved. Aside from some nicks in the armour though, the bot basically suffered no damage, and due to the format I still had a chance to bring it back through the Rumble Bee!

Fight 5 VS. Rust In Pieces, Phoenix, Claws 2, Jay, Daedalus:

I was feeling pretty confident in having a good tussle with the other control bots in the match, but having the most destructive vert in Phoenix (Ralf Schneider) and the most destructive horizontal in Daedalus (Cosmin Gorgovan) really offered a challenge in deciding who to go for much like the redemption fight earlier (bonus fact: the Shark Setrakian joke you see in the episode was the second take, the first got a bigger laugh, but required a retake so couldn’t be used).

https://www.youtube.com/watch?v=ZLhEuCA-5A0
Fight starts at 18:56.

I started immediately trying to stop Daedalus from getting up to speed, though unfortunately one of the hits it managed to get on me managed to get underneath the side armour and clip the left side of the drive, crippling the bot for the rest of the fight. From here I was able to crab-walk, hoping I could outlast the other competitors and stay aggressive enough to win a judges decision if it came to that. All the crab-walking put a lot of pressure on the 3D printed wheels though, and after a while, the hub rounded out, giving me no way to generate motion, and Léim Thart was finally eliminated from the competition after surviving a surprising amount of time in the rumble.

https://i.imgur.com/2rx2ji5.jpg
Léim Thart post-Daedalus.

Though it doesn’t look like too much happened, quite an amount of damage was done by Daedalus in that last match. Outside of the bite marks in the HDPE, the drive motor mounts on the left side had cracked, the weapon motor mount had bent from the shocks, and the drive bulkhead mounting bolt was actually pulled through the HDPE base. This was all repairable, but it showed that Daedalus was no joke, and that I’d need better armour in the future to stand a chance against machines like it. I actually managed to get the bot back working for a potential fight in the international special, but that opportunity never came to be, which was understandable given the time constraints (AnnieRUOK definitely should have gotten one though imo).

https://i.imgur.com/Pz1TATu.jpg
The cracked custom motor mount.

https://i.imgur.com/Jgf8mo7.jpg
the front of the bot where one of the bolts had been pulled through.

Conclusion:

Bugglebots 2019 went a lot better for me than last year, and I had an absolute blast over there both in and out of fights. Bristol is a lovely place with lovely people, and the improvements made to the competition and the show were plain to see. While the springs didn’t work quite as well as I’d hoped, I at least had a bot with an active weapon in the four-bar, and the drive system outperformed all expectations I had for it. I intend to give springs one more chance one day, but I’m going to try out some different designs for the near future that will hopefully be more effective in future live events. This iteration of Léim doesn’t actually stop with this event though, as there’s one more part of the story left over…

https://i.imgur.com/9X4HX3s.jpg
One last beer I picked up before leaving Bristol. Tasted good, and 10/10 presentation.

Techno Events/FRA Beetleweight Championship 2019

During Bugglebots I really enjoyed controlling Léim Thart as a wedge, and seeing that there was one more event in the form of the BW Championships in Marlow I decided to throw my hat into that for once with a build that needed little effort on my end. Being in such an awkward location, and being a little strapped for cash for the event, I had the brilliant idea of avoiding paying for accommodation by flying to Luton late at night, spending the night at the airport, going to the event, competing, and flying out that same night, all while not sleeping (Warning: this is NOT a good idea, do NOT try this, coffee can only get you so far).

I didn’t want to enter the same bot in however, and so I elected to make a few modifications to the design. First, I ditched the weapon and increased the armour at the front and top of the bot. Secondly, I printed slightly larger rear wheels so that I could actually drive while upside down. Finally, I completely redid the theme of the bot. I had been binging a bass-themed channel on YouTube called Davie504, and his videos often featured funny challenges (eg. playing Red Hot Chili Peppers with a red hot chili pepper, playing Guns N’ Roses with guns and roses). So in keeping with that theme, I put a bluetooth speaker into the robot, and during fights, I would play a bass cover of the RHCP’s song *Go Robot*. One visit to a printing shop later, and the bot had a new identity, Go Robot But Played On An Actual Robot. I arrived, passed tech checks, and was ready to compete with little issue.

https://i.imgur.com/5uX7750.jpg

https://i.imgur.com/Y8Ah72n.jpg
SLAP like now.

Fight 1 VS. X-301, Puns N’ Roses:

This first fight was an intimidating one. Puns N’ Roses (Sarah Malyan) was a near-indestructible brick, and X-301 (Cosmin Gorgovan) was the reigning champion, and Cosmin had already been on an incredible streak of event wins, the most recent being the FW champs.

https://youtu.be/bNhk6oOzLTA
Fight starts at 11:19

This ended up being quite a fun fight! The bot managed to stand up quite well to the hits from X-301, and it was a dream to control, allowing me to orbit the drum spinner and keep it under pressure. Unfortunately around 40 seconds in I started to notice I wasn’t getting much traction, and one more hit from X-301 left me unable to move, triggering the count-out and sending me to the losers melee. It seems that the wheels had rounded themselves out, but this happened far faster than it had last event, where I could get two or three fights out of them. Nonetheless, I replaced the rounded out ones, and got ready for the next fight. Worst of all though, the speaker I was using was far too quiet, and you couldn't hear it during the fight at all. Dammit!

Fight 2 VS. Puns N’ Roses, Suijin, K2:

https://youtu.be/mSMb-7pYmHM
Fight starts at 9:56

Usually you’d expect to fight some weaker machines in the losers melees, but this fight left me competing with two time Bugglebots champion K2 (Mark Leigh), which had fully recovered after a devastating shock loss to Wajoo. I managed to have a small tussle with him while Puns N’ Roses tussled with Suijin (Morgan Ls), and the bigger wheels allowed me to drive upside down for the first time! I kept the pressure up, but after a while I had ended up underneath K2 when the wheels rounded out again, leaving all three of us stuck. After the unstick Go Robot was officially counted out, ending the competition with an 0-2 record.

It was disappointing to do so badly at this event, but I did learn a lot from it. Most importantly, the increase in wheel diameter put more force on the 3D printed wheels, which resulted in them failing far earlier. This tells me that for future competitions I’d need to think of new and better ways of mounting wheels. Other than that though, that’s it with Léim Thart. I mostly use the chassis now as driving practice for my dad, and while I have CAD’s partway done for a Léim Three, there’s a lot I’d need to source before starting a build. This was a fun build log, and I hope to compete at more beetle events in the future, they’re always a blast! Next time there's a Bristol event or a Battle in the 'Burgh, I'm gonna try to go for sure!

https://i.imgur.com/FCx6Ws7.jpg
If I ever make a Go Robot 2, this will be the upgrade done to the speaker system.