Velociraptor's Fanfic Tournament - Series 7!

Infusion
Motivation: 4 x 125mm wheels
Speed: 0-12MPH [25MPH under Kinetic Boost]
Clearance: 7.5mm (same inverted) 0mm at the front, the wedge scraps the floor.
Weight: 100kg
Height: 125mm
Length: 800mm
Width: 600mm
Weapon: The weapon is a 31kg Hardox spinning ring (Ala MDU) powered by a LEM170 @ 36v. The rim rotates at 1800rpm and should spin up within 2-3 seconds max. The weapon is also a storage device for the drive. The spinning rim is connected to each side of the drive via a car air conditioner clutch, when the clutches are engaged, the 31kg kinetic storage bank(the spinning rim) transfers its energy into the drive train, giving it approximately double torque and speed for 2-3 seconds until the rim starts too loose speed and energy. This extra €˜kinetic€™ boost is used to ram into opponents with the front 10mm thick Hardox 500 wedge (similar to the one on Warrior SKF but wider and less depth to it). The front wedge is rubber shock mounted to ensure it survives the biggest of hits.
Drive: 2 x C40-500 Magmotors on 36v geared 7.5:1. The drive is also assisted via the spinning rim as explain above.
Batteries: 90 x 3600mAh NiCD Cells configured into 3 x 36v packs. This gives an output of 36v @ 10.8Amp/hours.
Armour: Front wedge is made entirely out of 10mm Hardox 500, the top and bottom of the robot is made out of 8mm Titanium/Vandium, The ring is made out of 10mm Hardox 400 with inner bracing to the perimeter bearing. Inner bulk heads are made from 20mm polycarbonate and 10mm aluminium.
Notes: Invertible, and generally well controlled for a spinner.

if theres any places left and if you are allowed real robots then Ill pick spartacus

There are four places left, Tim, and real robots are allowed, but you need to enter eight robots.

(Message edited by velociraptor on October 10, 2005)

Sorry Rich, but the stats might take a while. My good-for-nothing computer has finally bit the dust and itll have to spend some time in the repair shop. Im posting on my moms computer now, if you were wondering how I was able to with my busted computer.

I still need stats from Martijn, Daniel, Martyn and AJ.

I also need confirmed entrants in the following events from the following people:
MW: Tony (but hes got an excuse), AJ, Aaron, Alex M
LW: Tony, AJ, Aaron, Alex M
FW: Same four people
AW: Same again
SHW: Steven, AJ, Alex M
Annihilator: Dave Westons second entry, AJ, Martijn, Alex M
Challenge Belt: AJ, Alex M
HRR: AJ, Alex M

Ive got my SHW, AW, and MW done. Plus Ive finished CADing my FW, and stats for that will be up shortly. Now to finish my LW...

Heres three of my vapours, four to go:

Name - A Night at the Bar

Shape - A wide cylinder-shaped axlebot

Weight - 100 Kilogram

Speed - 24 km/h (15mph, geared for control)

Dimensions - 25x110x25 cm

Ground Clearance - Well, it€™s an axlebot€¦

Power - 2 S28-400 Magmotors at 24 volt

Movement - Two axlebot wheels, 25cm diameter

Turning Circle - Zero

Weaponry - In the middle of the cylinder, at 5 cm above the floor, is a 60 cm hardox bar with thick tungsten teeth on it. It weighs 25 kilogram and is powered by a B42-500Magmotor at 36 volt, spinning at 2000 rpm, giving it a nice spin up time. It€™s able to poop 55 kJ of energy straight into any opponent, so ha! The bar is mounted in such a way that it sticks out from the front and from the back, basically making it a double-headed spinning bar.

The only reason my bot can keep on driving normally even though it has only two wheels on the floor is because the centre of gravity is somewhere near the middle of the two teeth.

Armour - If you split the cylinder in halve, horizontally, the upper part of it is 4,5 mm hardox, and the lower part 5 mm, which is to centre the weight around the lower part, which is needed for the srimech. The insides are made shockproof with rubber, so it won€™t be destroyed by it€™s own weapon.

Srimech - Seeing there is a huge bar spinning in front and at the back of the bot, chances are a wedge won€™t be able to get underneath it from there anyway.
IF it is flipped, the bar will stop spinning and glide inside the cylinder, where it perfectly fits. At that point the bot is an almost perfect cylinder, and will be able to roll. The centre of gravity will roll in such a way that it will point downwards. As I designed it, the centre of gravity should be somewhere in the middle of the tungsten teeth, therefore it will roll to the position shown on the pick, and the bar will be put on again.

Strenghts - Devastating weaponry sticking out at the front and back, at only 5 cm above the floor. Should be able to fend off wedges.
Weakness - Can bounce off though armour, or the arena wall, or even the arena floor when the cylinder topples. And seeing my ONLY contact with the floor is the two wheels, this might become a rocking chair on steroids. Won€™t be pushing very much either.

Here€™s a pic; http://jupiter.walagata.com/w/madbull/Bar.gifhttp://jupiter.walagata.com/w/madbull/Bar.gif

Name - Axe to Fall

Shape - Take a cylinder, cut it in halve, and then put it on the ground, rectangular side heading downwards. The straight ends are the left and right sides, and are sloped. (Well, just take a look at the picture =P )

Weight - 100 Kilogram

Speed - 24 km/h (15 mph)

Dimensions - 115x80x40 cm (due to axe hanging out, main body is 80x80x40 cm)

Ground Clearance - 0 at front, 7 mm anywhere else

Power - 2x LEM130s at 48v

Movement - Four inner wheels, 10cm diameter

Turning Circle - Zero

Weaponry - The main weapon is a 5 kg double-headed axe on top of the machine, it€™s a steel 80 cm shaft with two diamond edged blades made of hardox on the end of it. The blades are shaped like the Mortis€™ blades, in order to create some nice slices into opposing armour.
The whole axe is powered by 2 nitrogen bottles at 1000 psi, a 1 kg buffer bottle and a 30 mm bore ram, for fast and furious hits, with a downforce of almost 2 ton brought onto a fine blade, and an energy unleash which seems significantly higher than for example Beta€™s if my calculations are right.

At the front of Axe to Fall is a small wedge/ram made out of 8 mm Titanium, to lift my opponent€™s wheels into air while clobbering them with my blade, or perhaps even to grab him. This ram is also my plan B if my axe fails in battle, just ram them hard using my good traction.

Armour - 8 mm Titanium front and 15 mm polycarb for the rest of the bot.
There are also two small blocks of vulcanized rubber on the mid-front and the mid-back of my machine, to absorb the downforce where the axe hits the chassis.


Srimech - The axe acts as a srimech, thanks to the curved shape of the top my bot can self right in no time, even if it has to self right over the wedged front (the wedge is very small mind you).
To make sure my bot won€™t end up on his side, I created a pair of curves on both sides, as can be seen on the picture.

Strengths - Destructive weapon, quick at self righting
Weakness - Weapon only works when opponent is in front of or behind the machine.

http://jupiter.walagata.com/w/madbull/Axe2.gifhttp://jupiter.walagata.com/w/madbull/Axe2.gif

Name - Back to Rock II

Shape - A box with a slightly sloped front

Weight - 100 Kilogram

Speed - 29 km/h (18mph)

Dimensions - 90x75x30 cm

Ground Clearance - 0 at sides and front, 2 mm at the back

Power - 2x Etek motors at 48 volt

Movement - Four wheels, 20cm diameter

Turning Circel - Zero

Weaponry - It has a broad hydraulic lifting arm which can easily lift 200 kg. To easily get underneath an opponent, it has two lifting plates at the bottom of the arm, one on the left end and one on the right end, instead of one large lifting plate like Behemoth.

Between the two plates, in the centre of the scoop, I mounted a vertical diamond edged Pussycat-style blade, powered by a S28-150 Magmotor, spinning upwards at approximately 3000 RPM, which will hopefully rip off some armour, or more likely, a tire, while lifting an opponent. Jamming a blade into an opponent while lifting it hopefully provides as much control over an opponent than a Behemoth-style grabbing claw/axe can, and it€™ll surely do more damage. (To avoid confusion, the blade is actually part of the lifter, so when the lifter moves up, the blade moves along).

On both sides of the bots is a pair of 5 mm titanium skirts, to make sure I won€™t get flipped very often, as hydraulic srimechs just aren€™t as fast as pnuematic ones.

Armour - 6 mm titanium all around

Srimech - The lifter self-rights the robot when needed

Strenghts - Nice weapon synergy, high traction, low ground clearance
Weakness - Hydraulic srimech might prove to be slow

A picture can be found here: http://jupiter.walagata.com/w/madbull/BacktoRockII.gifhttp://jupiter.walagata.com/w/madbull/BacktoRockII.gif


Ill enter Back to Rock II for the House Robot Rebellion
A Night at the Bar will be one of my two entries for the annihalator

Soz, havent had a lot of time cos of school. Ill stick with my VFT6 entrants if I can, and Ill have a random realie

Thats OK, Daniel. The realie you entered last time was Mr Nasty - do you want to enter that this time or a different one?

Because I know how crap my bots are Ill enter 8 realies
wheely big cheese
flippa
spartacus
pulverizer
gravity
tough as nails
snake bite
and rambot
wheely big cheese, rambot and tough as nails for the annihlator(if theres any spaces left

(Message edited by dogbot4000 on October 11, 2005)

You can only have 2 robots in the annihilator.

And Gravitys already been entered.

3 places left in the main comp, and entries for the Annihilator are now closed.

Alright, Ive got it.

My HWs:
Team Targeted -

Malaria
Cosmic Thunder
Cacodemon
Scorpion Bite 2 (New pictures up soon)
FBSDS
Flank Attack: DV
The Windmill
Voltronic (BB Season 5)

Otherweights:

AW: Pit Drone
FW: Neowedge
LW: Feedback
MW: The Templar
SHW: Tank: Panzer Divison

Side Comps:

Annihilator: Scorpion Bite 2, and Cosmic Thunder
Challenge Belt: Cacodemon
HRR: FBSDS

All stats here:
http://farr.proboards21.com/index.cgi?board=targetedhttp://farr.proboards21.com/index.cgi?board=targeted

This will be my 5th entry for the main tournament, and my second entry for the annihilator:

Name - Flick of the Wrist

Shape - 6-wheeled Tornado, including the angled rear to keep in contact with the ground while driving up a wedge

Weight - 100 Kilogram

Speed - 35 km/h (22mph)

Dimensions - 120x80x20 cm

Ground Clearance - 10 mm under the main body, variable clearance under the lifting spikes, with 0 mm as a minimum

Power - 2 B42-500 Magmotors at 48 volt

Movement - 6 wheels for awesome traction

Turning Circle - Zero

Weaponry - A pair of hardox, diamond tipped electric lifting spikes, a lot like the lifting spatula of American SHW Vladiator. These are 25 cm in length and can be lifted downwards which turns them into an active invertible lifting wedge. They can also be raised parallel to the floor, so they can act as a pair of classic ramming spikes. A 100 kg robot driving around at 22 mph is good for 5 kJ of kinetic energy. When this is brought onto a pair of diamond tipped spikes, this might seriously harm some armours.

Armour - 7 mm titanium all around

Srimech - It€™s invertible

Strenghts - High speed rambot, awesome traction
Weakness - Lack of devestating weapons

Here€™s a picture: http://jupiter.walagata.com/w/madbull/Flick.gifhttp://jupiter.walagata.com/w/madbull/Flick.gif

Would you be able to reserve me TAN for my HW real robot and Typhoon as a middleweight please Richard?

Just need to finish off one HW and an AW and then my squad is complete.

Sorry AJ, Timothys already entered TAN.

Name-Forklift 2
SHAPE- Low box with rear anti self flipping wedge
COLOUR- Yellowy orange
WEIGHT- 100kg
SPEED- 18mph
TURNING CIRCLE- 0m
GROUND CLEARANCE- 0mm at front due to flipper, 0mm at sides due to skirts 7mm with out, 0mm at rear due to wedge. The skirts are held down by torsion springs
ARMOUR- 3mm hardox
WHEELS- has 6 inner storm 2 style wheels
POWER- 2 x S28 Magmotors on 24v.
WEAPONS- it now uses a flipping arm that works much like the matadors or Toro€™s the flipper is powered by co2 on a 120mm pneumatic ram, working at 145psi, the flipper front is pretty unique as its front is like that of a fork lift (it has 2 flat bits of metal) this is welded onto the flipper, the arm can toss robots very high and if possible out of the arena. The prongs of the forklift weapon are used to get under the corners or gaps of skirts
SRIMECH- the flipper self rights the robot but because of the rear wedge thing it self rights like firestorm does i.e. the front wheels will go down first
NOTES- this is a modified version of my robot from the panic attack forum.
STRENGTHS- Power full weapon
WEAKNESSES- limited co2

NAME- The deer (was crusher chaos)
SHAPE- Invertible box
COLOR- the robot and claws are a dark green color
WEIGHT- 100kg
DIMENSIONS- 1m x 80cm x 25cm (l,w,h)
SPEED- 15mph
TURNING CIRCLE- 0mm
GROUND CLEARANCE- It has 6mm at the front due to the claws and has 0mm at the sides and rear without skirts 6mm. The skirts also work both ways up.
ARMOUR- 3.6mm hardox
MOVEMENT- 4 inner wheels that make the robot invertible
POWER- 2 x S28 Magmotors on 24v.
WEAPONS- it has a front pair of horizontal hydraulic crushing claws set up like deers antlers like you fine in extreme destruction. The claws have 3.5 tones of crushing force on the front tips of the claws at the middle is 6tones and right at the back it has 8 tones of crush. The claws are powered by hydraulics through a 120mm bore rams at 3000psi
NOTES- invertible, wide base means I wont topple while the deer is crushing
STRENGTHS- Very powerful weapon
WEAKNESSES- it could be turned into venison

NAME- Disco tech 2 (replacing disco 5)
SHAPE- Invertible box
COLOR- silver
WEIGHT- 100kg
SPEED- 20mph
TURNING CIRCLE- 0mm
GROUND CLEARANCE- 6mm under the discs has 0mm at sides due to skirts that will work when flipped
ARMOUR- 3.6mm hardox
WHEELS- it has 6 inner wheels
POWER- Drive: 2 x S28-400 Magmotors @ 36v with a 10:1 Mod 2 spur gear reduction connected to the 6 wheels.
Batteries: 120 x 3000mAh NiCD cells producing 36v @ 9amp
WEAPONS- It has 2 spinning each spinning at 3000rpm. Has a 4.00 second spin up time due to the C40-500 Magmotor on 36v with a 2:1 twin tension cog belt reduction. The flywheels produce 31.5Kj€™s at maximum RPM but is lethal at around 1 second. It has one weapon on the front and one on the back
SRIMECH- Invertible
NOTES- can spin on the spot
STRENGTHS- fast, powerful weapons, good pushing power
WEAKNESSES- easy to flip if discs aren€™t spinning

NAME- King 25 (previously 25€™s revenge)
SHAPE- Invertible disc like in the rw€™games or gyrobot
COLOUR- The robot is yellow and the bars are grey with black tipped ends
WEIGHT- 120kg
DIMENSIONS- 80cm diameter X 30cm (with out the bars)
SPEED- 8mph
TURNING CIRCLE- 0mm
GROUND CLEARANCE- 6mm both ways up
ARMOUR- the armour of the shell isn€™t much as nothing can get to it because of the weapon so it is, the armour is 3mm aluminium, the bars are made from titanium, the tips are tipped with tungsten
MOVEMENT - The robot is a shuffler which works both ways up
POWER- 2 x S28 Magmotors on 24v.
WEAPONS- Ok its has two interchangeable weapons the first is based on son of whyachi but not quite like it. The robot has the 3 triangle spinning bars like SoW but they are attached to the centre outer rim of the robot, the other is a sort of tornado like anti crusher cage but it is circular and runs on the floor its designed for robots with skirts and other stuff but I will explain better later, it is hinged so if flipped works both ways up (please say if this doesn€™t make sense) the weapon spins round at around 3500rpm this is designed to make a robot like SoW that cant be flipped over and immobilized the spinning outer shell is powered by 2 B42-500 Magmotors at 36volts, the bars/ skirts stick out around 1 meter which should prevent most robots from hitting the body.
NOTES- all components are shock mounted with rubber to survive its own blows and pushy bots.
STRENGTHS- Invertible, has powerful weapon, the top and bottom both ways can€™t be hit by axes or crushers due to the bars, may not fit in a pit
WEAKNESSES- easy to push if weapon isn€™t spinning

Name- Take me out (thanks to Dave for naming the robot for me)
SHAPE- Wedge
COLOUR- Dark grey
WEIGHT- 100kg
DIMENSIONS- Height: 20cm, Length: 80cm, Width: 65cm
SPEED- around 18mph
TURNING CIRCLE- 0mm
GROUND CLEARANCE- 0mm at the front due to wedge extender, 5mm at sides and rear
ARMOUR- 4mm Aluminium Boron Carbite
MOVEMENT- 4 inner vulcalon wheels, it uses a skid steer system like tornado
DRIVE- 2 LEM 130€™S on 36 volts
BATTERIES- custom 3300mAh NiCad Cell 36v BotPack
WEAPONS- The robot has a 1000psi nitrogen flipper on a 80mm bore on a 100-stroke ram which should make around 3.5 tones at the ram (if I am incorrect please correct me) the nitrogen is stored in 2, 2.2kg canisters, the robot has around 25 flips in a fight, the flipper is on high pressure
STRENGTHS- Powerful weapon, good drive
WEAKNESSES- limited supply for the weapon

NAME- Wind Chaser
SHAPE- Invertible wedge with curved rear
COLOUR- white with 1 pink line on each side
WEIGHT- around 96kg
SPEED- 25mph
TURNING CIRCLE- 0mm
GROUND CLEARANCE- 0mm at the front due to wedge, 0mm at sides due to skirts 5mm at back
ARMOUR- 4mm Hardox
MOVEMENT- it has 6 inner vulcalon wheels
POWER- it uses 2 x lem 130€™s on 48volts
WEAPONS- It has a rear hinged flipping arm, powered by a lem 130 on 60volts, so it can easily get a robot out of the arena.
STRENGTHS- Compact in size, great pushing power, powerful weapn
WEAKNESSES- no rear skirt, no weapon when flipped.

Panic Attack (Ex 2)
Razer (series 6)


Also save me a space in the other weights and anyother side events that have spaces

okay I choose rippa or if thats chosen pulveriser

I dont ever rember a robot called rippa i know there is one called ripper but i am sure rippa isnt real

Razers already been entered, Martyn. And youll only be able to fit into the antweights and superheavyweights for the other weights, and the Challenge Belt and House Robot Rebellion.

And I dont know which Rippa you mean, Timothy - could you please specify? Also, could you please say which of your two real robots are going into the Annihilator?

(Message edited by velociraptor on October 13, 2005)

Ill have Big Nipper as my realie then please (if thats not taken that is).

Just gotta finish of my ant and then Ill post my team.

When do the battles start?

When all the entries are in, and I still need stats from some people and 3 people to enter.

Name: Instant Zen
Motivation: 2WD
Speed: 20cm/sec
Weight: 150g
Height: 30mm
Length: 100mm
Width: 75mm
Weapon: 35g Titanium spinning shell powered by a Torcman 200-5-18 motor geared 1:1 at 8000rpm.Second weapon is a thin .75mm titanium wedge power from the spinning shell via a 5g micro servo that pushes a nub into one of the cam bumps on the spinning shell. This fires the little flipper with enough force to toss a 150g weight 100-250mm into the air.
Drive: 2 x 8gram Sanyo NA 75:1 gearmotors with 20mm foam wheels
Batteries: A single 11.1v 340mAh Kokam Lithium Polymer battery pack.
Armor: titanium spinning shell protects the top and sides, a 1mm aluminium base plate protects the underbelly
Notes: selfright via mauler dance. Uses a pair of scorpion single channel speed controllers and a phoenix 15 brushless controller for the weapon. Everything is opoxied together. No weight left for anything else to hold it together :proud:

WEAPONS- It has a rear hinged flipping arm, powered by a lem 130 on 60volts

FIRE! I smell a cooked Lem 130.... :proud: Lem 130 is a 12-24v motor with the ability to go to 36v with current limiting. 48v is asking a hell of a lot. Check out the specs on the Lemco website, youll find some usefull information on them there.

Hi again.

Ill enter Flipping Hell as my 2nd Annihilator entrant, ok Richard ?

Rippa the robot in Series 7 the robot which I think one of the team members(Driver Im not sure) came from the Kan-Opener that one. the two realies in the annihlator are WBC and TAN

(Message edited by dogbot4000 on October 14, 2005)

RippER, mate. RippER. :wink:

Anyways, heres my Superheavyweight to complete my line-up. Originally made for AI:PIE, please put your drumsticks together for Revolver! :proud:

NAME- Revolver (SHW)
SHAPE- box wi skirted sides and rear
COLOUR- painted like the infamous Yellow Submarine with portholes on the sides n that, with red hinged skirting and the cover for the album Revolver pasted on the top
WEIGHT- under 150kg, hopefully
DIMENSIONS- 110cm X 75cm X 28cm
SPEED- 18mph
TURNING CIRCLE- 0m
GROUND CLEARANCE- 10mm all over without skirts, 0mm at sides n rear with em
ARMOUR- 6.75mm monocoque Hardox. Booyah.
MOVEMENT- 4 inner wheels and a little caster on top/bottom at the front for balance
POWER- 2 x C40-500 MagMotors, running at 36v (should give about 12hp, I think)
WEAPONS- The main weapon here is a large horizontal spinning disc at the front resembling an LP record. This is powered by an LEM-130 motor at 36v and runs at around 2500rpm. The flywheel bears two Hardox teeth (curved ala Pussycats), making it ideal for ripping into the other contestants. It could also charge at other competitors, get under them with the skirt and become a passive rammer should things start to get hairy.
SRIMECH- invertible
NOTES- flies the Scotland flag
STRENGTHS- powerful disc, fast, manoueverable, pushing power, invertible
WEAKNESSES- wheels exposed to overhead attacks, control could be an issue

Picture here: http://70.85.81.229/3670/198/upload/p745854.jpghttp://70.85.81.229/3670/198/upload/p745854.jpg

Heres hoping thats OK :)

Youve already entered Flipping Hell in the HRR, Dave, so it needs to be a different one - sorry. And Ill assume Timothy means Ripper, the flipping robot that lost to Firestorm in the heat final.

Team Code_14

1) Big Nipper
2) http://teamcode14.proboards24.com/in...ead=1103744395

Thanks, AJ!

Flaming Hell (Dave Weston)
Hell Machine (Dave Weston)
Sheer Hell (Dave Weston)
Flipping Hell (Dave Weston)
Jaws Of Hell (Dave Weston)
Helliant (Dave Weston)
All Hell (Dave Weston)
Razer (Dave Weston)
Wedge Devolution (Steven MacGregor)
Killotine: EVO (Steven MacGregor)
S.D. IV (Steven MacGregor)
Whirligig 4.0 (Steven MacGregor)
Revenge of the Revenge of the Bludgeonator! (Steven MacGregor)
Toby the T-Ram Engine (Steven MacGregor)
Tails (Steven MacGregor)
Chaos 2 (Steven MacGregor)
SUNCUST (Anthony Politzi)
Shovearoud 2 (Anthony Politzi)
Cyberdemon (Anthony Politzi)
Psycho Cyan Evolved (Anthony Politzi)
Bloody Tears 2 (Anthony Politzi)
Judo Chop! (Anthony Politzi)
Mr. Slave 2 (Anthony Politzi)
Spawn Again (Anthony Politzi)
Beta (Martijn Benschop)
A Night At The Bar (Martijn Benschop)
Back To Rock II (Martijn Benschop)
Axe To Fall (Martijn Benschop)
Flick Of The Wrist (Martijn Benschop)
(Martijn Benschop)
(Martijn Benschop)
(Martijn Benschop)
Firestorm V (Kevin Smith)
Storm 2 (Kevin Smith)
Mute (Kevin Smith)
Atomic (Kevin Smith)
Gravity (Kevin Smith)
Dantomkia (Kevin Smith)
Wolf (Kevin Smith)
Enterprise (Kevin Smith)
Manic Monsoon (Daniel Stickler)
Dallas (Daniel Stickler)
Dervish V/ (Daniel Stickler)
Wheely Pure Evil 2 (Daniel Stickler)
Sonic Boom (Daniel Stickler)
Squish (Daniel Stickler)
Ringmaster (Daniel Stickler)
(Daniel Stickler)
Forklift 2 (Martyn)
The Deer (Martyn)
Disco Tech 2 (Martyn)
King 25 (Martyn)
Take Me Out (Martyn)
Wind Chaser (Martyn)
Panic Attack (Martyn)
(Martyn)
Overkill (Chris Mason)
Orka Mk4 (Chris Mason)
Dieceratops Reinvertus (Chris Mason)
Cyclone Force 2.5 (Chris Mason)
Leprosy Infection (Chris Mason)
Mega Masher 2 (Chris Mason)
Axeolotl (Chris Mason)
Obliteration (Chris Mason)
Big Nipper (AJ)
SOR 5.0 (AJ)
Wedga Revo 2.0 (AJ)
Forcepower 5.0 (AJ)
Psyclonised (AJ)
Geforce 4.0 (AJ)
Gigabyte 1.5 (AJ)
Yet Another Cut Above The Rest (AJ)
Mortis (Alex Holt)
Tengu 7 (Alex Holt)
Black Panther Queen (Alex Holt)
Kali (Alex Holt)
Dante (Alex Holt)
Achilles (Alex Holt)
Salamander III (Alex Holt)
Scaramanga II (Alex Holt)
Mass Disctruction Ultimate 3 (Aaron Knight)
Rogue (Aaron Knight)
Intensity (Aaron Knight)
MOABIE (Aaron Knight)
Infusion (Aaron Knight)
The Ultimate Wedge (Aaron Knight)
Sewer Snake (Aaron Knight)
Warrior SKF (Aaron Knight)
Malaria (Alex M & W)
Cosmic Thunder (Alex M & W)
Cacodemon (Alex M & W)
Scorpion Bite 2 (Alex M & W)
FBSDS (Alex M & W)
Flank Attack: DV (Alex M & W)
The Windmill (Alex M & W)
Voltronic (Alex M & W)
Wheely Big Cheese (Timothy)
Flippa (Timothy)
Spartacus (Timothy)
Pulveriser (Timothy)
Tough As Nails (Timothy)
Snakebite (Timothy)
Rambot (Timothy)
Ripper (Timothy)

MW - closed
Hell Fire (Dave Weston)
Killoteeny (Steven MacGregor)
(Anthony Politzi)
Tom (Chris Mason)
Typhoon (AJ)
Blizzard (Alex Holt)
(Aaron)
The Templar (Alex M)

LW - closed
Hell Hound (Dave Weston)
Minigig (Steven MacGregor)
(Anthony Politzi)
Little Big Bot (Chris Mason)
Miniforce (AJ)
Tiny Tengu (Alex Holt)
(Aaron)
Feedback (Alex M)

FW - closed
Hells Angel (Dave Weston)
Aries (Steven MacGregor)
(Anthony Politzi)
Ram Raider (Chris Mason)
Overdrive (AJ)
Sith (Alex Holt)
(Aaron)
Neowedge (Alex M)

AW - closed
Baby Hell (Dave Weston)
Wedge 3mm (Steven MacGregor)
(Anthony Politzi)
Tyrantosawrus Rex (Chris Mason)
Microforce 2.0 (AJ)
Instant Zen (Aaron)
Pit Drone (Alex M)
(Martyn)

SHW - closed
Revolver (Steven MacGregor)
Walk Away (Anthony Politzi)
Octopush 2 (Chris Mason)
Uberforce (AJ)
Red Knight (Alex Holt)
Gyrate Extreme (Aaron Knight)
Tank: Panzer Division (Alex M)
(Martyn)

ANNIHILATOR - closed
ROTROTB (Steven)
SD IV (Steven)
Bloody Tears 2 (Anthony)
Psycho Cyan Evolved (Anthony)
Hell Machine (David)
(David)
Orka Mk4 (Chris)
Axe-o-lotl (Chris)
Psyclonised (AJ)
Gigabyte 1.5 (AJ)
A Night At The Bar (Martijn)
Flick Of The Wrist (Martijin)
Kali (Alex)
Salamander III (Alex)
Cosmic Thunder (Alex M)
Scorpion Bite 2 (Alex M)
Wheely Big Cheese (Timothy)
Tough As Nails (Timothy)

CHALLENGE BELT
Killotine Evo (Steven)
SUNCUST (Anthony)
Flaming Hell (David)
Cyclone Force 2.5 (Chris)
Wedga Revo 2.0 (AJ)
Cacodemon (Alex M)
(Martyn)

HOUSE ROBOT REBELLION
Whirligig 4.0 (Steven)
Mr Slave 2 (Anthony)
Flipping Hell (David)
Obliteration (Chris)
Geforce 4.0 (AJ)
FBSDS (Alex M)
Back To Rock II (Martijn)
(Martyn)

Still needed:
*3 people to enter
*Three robots from Martijn
*One more bot, Vapour or real, from Martyn to replace Razer
*Confirmed real robot from Daniel
*Stats for Intensity and Ultimate Wedge from Aaron
*MWs from Anthony and Aaron
*LWs from Anthony and Aaron
*FWs from Anthony and Aaron
*AWs from Anthony and Martyn
*SHW from Martyn
*One more Annihilator entrant from Dave Weston
*Challenge Belt and HRR entrants from Martyn

(Message edited by velociraptor on October 15, 2005)

With some help from Andy [Thanks a TON Andy btw] Heres my ant:
Name: No Stairway to Heaven
Speed: 40cm per second
Weight: 16 oz, 1 pound, 0.5 kg, 150 grams, whatever you want to call it.
Motors: 4 27:1 ESCAP motors [12v] for drive. The drum on front is powered by a stinger motor [12v, if it can be run that high, I dont know alot about it]
Weapon: a drum weighing 2 ounces, running on 3000 RPM producing 20kjs.
Armor: 1mm kevlar on top and bottom, 1mm HDPE on the sides and back, and 1mm titaium on the front to prevent too much damage to the drum area.
Skirts: On the sides and back.
GC: About 0 all over thanks to skirts, 6mm at front.
Turning Circle: 0.
Strengths: Good all arounder, no serious weaknesses.
Weaknesses: Dosent excel in any one area, which might hurt it when going aginst a specialized bot.
[Dave [S], if you could post this in my stats forum with my password, id appreciate that]
[Also Rich, LW, MW, and FW might have to wait a while, depending on how mcuh help I can get from others, how long do I have left?]

Its been a week since you originally entered, Anthony, but I suppose I can afford to wait for other weights, since they wont be fighting until after the second semi final.

(Message edited by velociraptor on October 15, 2005)

Can I enter more robots for something?

Sorry, youve already entered 8 robots and all the other weights are full.

Mr Nasty will be fine thanks.

6 done, 2 to go :proud:

this bot will also enter the Challenge Belt

Name - Sheer Heart Attack

Shape - Invertible tracked box, only the main-body between the tracks is shorter then the tracks (as can be seen on the picture), build in such a way that the tracks are in contact with the ground no matter what (like 101), only with two titanium bars at the end of both tracks to protect them from destructive spinners

Weight - 110 Kilogram

Speed - 24 km/h (15 mph)

Dimensions - 90*100*25 cm

Ground Clearance - Zero underneath the tracks, but with an overhang

Power -2x LEM130s at 48v

Movement - Two sturdy titanium tracks, with rubber strips attached to them for traction

Turning Circle - Zero

Weaponry - A 22 kilogram titanium spinning drum at the front of my machine equipped with 10 hardox teeth, powered by a LEM 130 and spinning around at 5000 RPM, which produces nearly 40 kJ.

Armour - 6 mm titanium all around (including the tracks themselves)

Srimech - It€™s invertible

Strenghts - Devestating against most wedges, nice traction
Weakness - Exposed (but quite sturdy) tracks might be a weakness

Notes- I designed this robot to be a robot which gains it€™s advantage by driving OVER an opponent, a bit like Barberous. The exposed tracks are the ultimate way to keep in contact with the floor no matter what kind of ramp I drive up, so that if a good rambot or whatever gets underneath me in a threatening way, I can simply go in full reverse and escape. The drum, ofcourse, is a perfect way to hurt an opponent while he€™s underneath you.

Here€™s a picture: http://jupiter.walagata.com/w/madbull/Tracks2.gifhttp://jupiter.walagata.com/w/madbull/Tracks2.gif

Stats for No Stairway to Heaven changed:
Weight: 150 grams.
Speed: 40cm a second
Armor: 1mm HDPE on the sides and rear, 1mm kevlar on top and bottom, 1mm titanium on front.
Weapon: 1 ounce drum spinning at 3000 RPM, producing 12kjs.
Power: Run on 4 JP Supertech Naro Maxes on 6v. The weapon is powered by a stinger motor on 6v.
Notes: There is a plow so large it surronds the sides and rear. It does not cover the front, as not to get in the way of the plow.
GC: 0 at sides and rear thanks to plow. 5mm at front.
Turning circle: 0.
Strengths: Good all arounder, no real weaknesses.
Weakneses: Dosent excel at anything.

My 7th entry will be the realie Fluffy, my 8th entry will be:

Name - Liar

Shape - A bit like a non-invertible Wheely Big Cheese, it has a fairly wide wheel-to-wheel base at the back, while the front is a much smaller (and pretty long) wedge, the front of the wedge has to €œside wedges€ as can be seen on the pic

Weight - 100 Kilogram

Speed - 29 km/h (18mph)

Dimensions - 120x60x30 cm

Ground Clearance - 0 mm at the front and underneath €œside-wedges€, 7 mm anywhere else

Power - 2 S28-400 Magmotors at 24 volt

Movement - 2 inner wheels, 15 cm in diameter

Turning Circle - Zero

Weaponry - The wedge contains a 1000 psi titanium rear-hinged flipper (basically the red parts of the picture), powered by two pneumatic rams. It should be able to give a 100 kg robot a height of some meters. As can be seen in the picture, the flipper has two €œside-wedges€. I have added them since I saw that flippers tend to be quite weak when attacked at the back. When Liar is attacked at the back, he simply does the same as Stinger does when he goes into flail mode. By doing so, the side wedge will ram into the opponent and shove underneath it. That way I can use my flipper and get it on his back. Although this flip will not be as powerful as a frontal flip, it will be a flip nonetheless, and it will help me get rid of any threats that approach me from the back.

Armour - 8 mm titanium all around

Srimech - That flipper

Strenghts - Powerful and maneuverable flipper
Weakness - Won€™t be pushing much, won€™t be damaging much either

Here€™s a picture: http://jupiter.walagata.com/w/madbull/flip.gifhttp://jupiter.walagata.com/w/madbull/flip.gif

My real robot will be Suicidal Tendencies (series 5)

AntyB (aw)
Someones watching over me (shw)
Disco tech 2 (challange belt)
Take Me Out (HRR)