Tab Content
  • Ocracoke's Avatar
    Yesterday, 20:03
    They are Gimson 13.7:1 motors (https://gimsonrobotics.co.uk/categories/dc-electric-motors/products/gr-ep-45-high-power-45mm-planetary-gearmotor). Coupled with 775 motors, they are a solid, if...
    100 replies | 10974 view(s)
  • Ocracoke's Avatar
    Yesterday, 19:46
    Azriel After finding a few moments to concentrate on this one, I've got it rolling. It isn't The Honey Badger quick but it is quite controllable as a result. Thanks to having the wiring loom, motors...
    100 replies | 10974 view(s)
  • Ocracoke's Avatar
    16th June 2019, 15:15
    Jibril So the gearbox sides have been cut and the gears are on the shaft for Jibril but I've yet to make any head way in actually building it. Given the now tight timelines to RL Grantham, I may not...
    100 replies | 10974 view(s)
  • Shakey's Avatar
    14th June 2019, 13:22
    If it helps I dug up the F2 data sheet (Still on the store, just tucked away): https://nutsandbots.co.uk/ftds/
    110 replies | 16515 view(s)
  • Ocracoke's Avatar
    13th June 2019, 13:32
    So the parts for the two stage reduction have arrived and I'll be cutting up the HDPE for both the gearbox and Azriel tonight. It did however strike me that I had forgotten the bearings! Bleh, they...
    100 replies | 10974 view(s)
  • Ocracoke's Avatar
    13th June 2019, 11:14
    You would need to wire it up in series (for increased voltage) or in parallel (for increased capacity) to get power to the ESC.
    110 replies | 16515 view(s)
  • Ocracoke's Avatar
    13th June 2019, 10:29
    Yes, Comet uses the 30A versions of the ESC. Not the same weight class but Jibril uses 10AWG wire with a pair of 4S 4200mAh LiFe batteries to drive both the drive and the Scythe (should probably...
    110 replies | 16515 view(s)
  • joebrown's Avatar
    11th June 2019, 14:16
    Hi! This is happening this Sunday and everyone is welcome, no sign ups required, bring your ants, come bodge a bodgebot :)
    1 replies | 405 view(s)
  • Ocracoke's Avatar
    10th June 2019, 16:58
    I was talking with Gareth (of Trolley Rage) about this and he suggested something very similar. In terms of an controller for axes, I guess you would want it to be a on-off affair to get maximum...
    100 replies | 10974 view(s)
  • Ocracoke's Avatar
    10th June 2019, 16:02
    I think you are referring to the 60A dual channel ESC? I am talking about the 40A single channel ESC, which is the next one down from the 60A. The 60A dual channel is a far more reliable controller...
    100 replies | 10974 view(s)
  • Ocracoke's Avatar
    9th June 2019, 17:33
    I think the ESC just isn't suitable for MWs full stop. It is a neat controller but it is too fragile in terms of the components out of the box but the high gearing will definitely not be helping....
    100 replies | 10974 view(s)
  • Ocracoke's Avatar
    9th June 2019, 15:12
    Yes, the new floor is going to be a one piece affair. Looking at 900mm squared 6mm polycarbonate at the moment, still not finalised the design just yet. EXR Guilford 2019 So Jibril went to EXR...
    100 replies | 10974 view(s)
  • Ocracoke's Avatar
    7th June 2019, 14:33
    Oooh, I'll hold you to that one :P I know Luke (Bad Wolf on here) does do advertising for BotFest as well. Hopefully. :D It'll run this Saturday come what may but for RL Grantham, it really...
    100 replies | 10974 view(s)
  • Ocracoke's Avatar
    7th June 2019, 12:52
    Hahhaa, will do. I've been wavering about going to EXR Guildford, RL Grantham and EXR Bolton but I think I'll be able to. If Jibil's refit with the new gearbox doesn't take too long (I should have it...
    100 replies | 10974 view(s)
  • Ocracoke's Avatar
    6th June 2019, 12:50
    Jibril I've tested the rebuilt axe mechanism and it's... fine... for now. It really will be better on the two stage gearbox as at the moment, it is a little "undertorqued" but then again, the high...
    100 replies | 10974 view(s)
  • Ocracoke's Avatar
    4th June 2019, 16:21
    Hi Colin, I know why I went for 10mm, it was the biggest HSS drill bit I had at the time and it allowed me to align everything nice and neatly. After EXR Bolton, I might ditch doing a rebuild...
    100 replies | 10974 view(s)
  • Ocracoke's Avatar
    4th June 2019, 12:41
    The bent driveshafts... probably a design flaw. They are only 10mm wide. A refit of Jibril will make them 12mm hardened steel but I might get away with 10mm hardened steel. Doesn't help they are...
    100 replies | 10974 view(s)
No More Results
About joebrown

Basic Information

Age
26
About joebrown
Name:
Joe Brown
Biography:
Runs Bristol Bot Builders. Passionate about Bristol and crab based robots.
Location:
Bristol
Occupation:
Elec Engineer
Robots:
Crabsolutely Clawful: FW, BW, Ant
team Two-Headed Death Flamingo: HW
Cluster Duck: BW, Ant
Sgt Tash

Statistics


Total Posts
Total Posts
17
Posts Per Day
0.04
General Information
Last Activity
Yesterday 08:15
Join Date
6th March 2018
Referrals
0

6 Friends

  1. Craaig 
    Status
    Offline

    Member

    Craaig
  2. Felix Townsend 
    Status
    Offline

    Roboteer

    Felix Townsend
  3. Ocracoke 
    Status
    Online

    Team Kaizen

    Ocracoke
  4. Rapidrory 
    Status
    Offline

    Member

    Rapidrory
  5. Scottie 
    Status
    Offline

    Member

    Scottie
  6. Shakey 
    Status
    Offline

    Member

    Shakey
Showing Friends 1 to 6 of 6