Tab Content
  • Ocracoke's Avatar
    Today, 02:16
    Jibril Well it has been a bit of a slog in places. Turns out the bolts I found were 80, not 90mm long and ended up having to carve up some 100mm long bolts to make proper length driveshafts on the...
    211 replies | 138227 view(s)
  • Ocracoke's Avatar
    18th February 2020, 15:16
    Hahahaa! It might be made to be scared a little sooner than I thought. I found some 90mm long bolts that will work as drive shafts and the shaft mounts will take a M6 bolt without adaptation (they...
    211 replies | 138227 view(s)
  • Ocracoke's Avatar
    17th February 2020, 23:21
    Following on from the last post, I've been busy. Tada! I'll be running out tomorrow to get some M10x100mm bolts or something to screw the motor mounts down with along with some coarse...
    211 replies | 138227 view(s)
  • Ocracoke's Avatar
    17th February 2020, 01:24
    Jibril So yeah, this weekend didn't go to plan. Managed to get the drive templates made but in cutting the drive shafts, need to go outside to that really and it has been too wet to do so. Still, I...
    211 replies | 138227 view(s)
  • Ocracoke's Avatar
    15th February 2020, 15:00
    We'll see closer to the time. Had a bit of a setback here which means I can't work on it this weekend. It'll happen.
    7 replies | 503 view(s)
  • Ocracoke's Avatar
    13th February 2020, 13:48
    Nope, no deadline really. Signups are open up until the event starts.
    7 replies | 503 view(s)
  • Ocracoke's Avatar
    13th February 2020, 10:06
    Excellent, glad to hear the event is being looking forwards to! With any luck, I will have the arena's floor lifted up a little over the weekend and the pit floor painted.
    7 replies | 503 view(s)
  • Ocracoke's Avatar
    10th February 2020, 22:41
    Hahahaa, true enough! I've got a 10mm spade bit somewhere, will bear that in mind for future use.
    211 replies | 138227 view(s)
  • Ocracoke's Avatar
    10th February 2020, 12:14
    It is time for the next BotFest event! Location St. Lukes Church Poulton Wallasey CH44 3BD Date 25th April 2020
    7 replies | 503 view(s)
  • Ocracoke's Avatar
    10th February 2020, 02:41
    Jibril The HDPE base panel has been drilled. Doing 32 holes three times over in 3, 8 and 10mm bits is nuts but there you are. Currently mocking up the motor mount bolt pattern on a 1mm sheet of...
    211 replies | 138227 view(s)
  • Ocracoke's Avatar
    9th February 2020, 00:13
    Ocracoke replied to a thread BOB FW Series in Build Diaries
    I'd recommend something thicker, like the thread cutting oil that Colin mentioned. WD40 is probably going to be too light for this.
    101 replies | 24388 view(s)
No More Results
About joebrown

Basic Information

Age
27
About joebrown
Name:
Joe Brown
Biography:
Runs Bristol Bot Builders. Passionate about Bristol and crab based robots.
Location:
Bristol
Occupation:
Elec Engineer
Robots:
Crabsolutely Clawful & Two-Headed Death Flamingo

Statistics


Total Posts
Total Posts
31
Posts Per Day
0.04
General Information
Last Activity
16th February 2020 10:17
Join Date
6th March 2018
Referrals
0

6 Friends

  1. Craaig 
    Status
    Offline

    Roboteer

    Craaig
  2. Felix Townsend 
    Status
    Offline

    Roboteer

    Felix Townsend
  3. Ocracoke 
    Status
    Offline

    Team Kaizen

    Ocracoke
  4. Rapidrory 
    Status
    Offline

    Member

    Rapidrory
  5. Scottie 
    Status
    Offline

    Member

    Scottie
  6. Shakey 
    Status
    Offline

    Member

    Shakey
Showing Friends 1 to 6 of 6