Tab Content
  • Ocracoke's Avatar
    Yesterday, 14:59
    Oh yes, hello! :D I think it is worth making a prototype of this with some old SLA batteries or something with a load and measure the voltage at each take off to see what happens. You could put in...
    3 replies | 103 view(s)
  • Ocracoke's Avatar
    Yesterday, 08:45
    Ocracoke replied to a thread FW- Crash Course in Featherweights
    Effectively, yes. A wire is attached to each end of the fuse holder and the fuse acts as a bridge.
    26 replies | 1948 view(s)
  • Ocracoke's Avatar
    28th September 2020, 16:58
    I run my heavier class robots with their batteries in series to up the voltage. These are matching pairs of voltages and capacities so I end up adding in just the one fuse, treating them as a single...
    3 replies | 103 view(s)
  • Ocracoke's Avatar
    28th September 2020, 16:40
    Ocracoke replied to a thread FW- Crash Course in Featherweights
    I get my 80A fuses from Halfords usually. They are wired inline from the battery. Here is one I made for a MW but the same rules apply for a FW. The fuse is in the maxi fuse holder at the top right...
    26 replies | 1948 view(s)
  • Ocracoke's Avatar
    23rd September 2020, 15:46
    PMed
    1 replies | 370 view(s)
  • Ocracoke's Avatar
    21st September 2020, 22:41
    Aye, just one of those things. Short of a miracle happening, I am not expecting to run an event now until next year. By then... BotFest might have a completely new arena. ;)
    68 replies | 8413 view(s)
  • Ocracoke's Avatar
    21st September 2020, 22:20
    Ocracoke replied to a thread FW- Crash Course in Featherweights
    I thought you meant on the receiver? The RC bits I have already have a JST-SH plug on them normally, it'd just push on and then some electrical tape over the wire, plug and RX to hold it in place.
    26 replies | 1948 view(s)
  • Bad Wolf's Avatar
    21st September 2020, 19:03
    Ahhh thats a real shame :( But totally out of everyones hands and just one of those things! On to 2021 now I guess and lets pretend 2020 never happened! Viva La Bot Fest!
    68 replies | 8413 view(s)
  • Ocracoke's Avatar
    21st September 2020, 18:07
    Ocracoke replied to a thread FW- Crash Course in Featherweights
    I use the pins that come on the receiver and put electrical tape around that and the board to keep it in. Have come a cropper with RC wires coming out before.
    26 replies | 1948 view(s)
  • Ocracoke's Avatar
    20th September 2020, 01:38
    Lafiel So the shell I posted a picture of in my last post didn't work. I could, amazingly, get it in size and weight but it was quite ugly and it wasn't very good overall so I ripped that apart and...
    269 replies | 157254 view(s)
  • Ocracoke's Avatar
    17th September 2020, 18:28
    Looks good, well done. Guessing a pair of drills for the drive and and linear actuator for the jaw?
    39 replies | 7281 view(s)
No More Results
About Bad Wolf

Basic Information

Date of Birth
June 19, 1988 (32)
About Bad Wolf
Name:
Bad Wolf
Biography:
Total Noob, but trying
Location:
North Wales

Statistics


Total Posts
Total Posts
110
Posts Per Day
0.11
General Information
Last Activity
21st September 2020 19:03
Join Date
2nd January 2018
Referrals
0

4 Friends

  1. Ocracoke 
    Status
    Offline

    Team Kaizen

    Ocracoke
  2. Retroman 
    Status
    Offline

    Roboteer

    Retroman
  3. Scottie 
    Status
    Offline

    Member

    Scottie
  4. Theo 
    Status
    Offline

    Roboteer

    Theo
Showing Friends 1 to 4 of 4