Tab Content
  • Ocracoke's Avatar
    Today, 02:16
    Jibril Well it has been a bit of a slog in places. Turns out the bolts I found were 80, not 90mm long and ended up having to carve up some 100mm long bolts to make proper length driveshafts on the...
    211 replies | 138197 view(s)
  • Ocracoke's Avatar
    18th February 2020, 15:16
    Hahahaa! It might be made to be scared a little sooner than I thought. I found some 90mm long bolts that will work as drive shafts and the shaft mounts will take a M6 bolt without adaptation (they...
    211 replies | 138197 view(s)
  • Ocracoke's Avatar
    17th February 2020, 23:21
    Following on from the last post, I've been busy. Tada! I'll be running out tomorrow to get some M10x100mm bolts or something to screw the motor mounts down with along with some coarse...
    211 replies | 138197 view(s)
  • Ocracoke's Avatar
    17th February 2020, 01:24
    Jibril So yeah, this weekend didn't go to plan. Managed to get the drive templates made but in cutting the drive shafts, need to go outside to that really and it has been too wet to do so. Still, I...
    211 replies | 138197 view(s)
  • Ocracoke's Avatar
    15th February 2020, 15:00
    We'll see closer to the time. Had a bit of a setback here which means I can't work on it this weekend. It'll happen.
    7 replies | 495 view(s)
  • Bad Wolf's Avatar
    13th February 2020, 21:10
    Yeah im excited to hopefully have some new bots sorted by then too! I have a couple of those strip LED lights if you need them, they plug into the mains they arnt battery though. Bad Wolf
    7 replies | 495 view(s)
  • Ocracoke's Avatar
    13th February 2020, 13:48
    Nope, no deadline really. Signups are open up until the event starts.
    7 replies | 495 view(s)
  • Ocracoke's Avatar
    13th February 2020, 10:06
    Excellent, glad to hear the event is being looking forwards to! With any luck, I will have the arena's floor lifted up a little over the weekend and the pit floor painted.
    7 replies | 495 view(s)
  • Ocracoke's Avatar
    10th February 2020, 22:41
    Hahahaa, true enough! I've got a 10mm spade bit somewhere, will bear that in mind for future use.
    211 replies | 138197 view(s)
  • Bad Wolf's Avatar
    10th February 2020, 21:18
    Cant wait for the event :) Bad Wolf
    7 replies | 495 view(s)
  • Ocracoke's Avatar
    10th February 2020, 12:14
    It is time for the next BotFest event! Location St. Lukes Church Poulton Wallasey CH44 3BD Date 25th April 2020
    7 replies | 495 view(s)
  • Ocracoke's Avatar
    10th February 2020, 02:41
    Jibril The HDPE base panel has been drilled. Doing 32 holes three times over in 3, 8 and 10mm bits is nuts but there you are. Currently mocking up the motor mount bolt pattern on a 1mm sheet of...
    211 replies | 138197 view(s)
  • Ocracoke's Avatar
    9th February 2020, 00:13
    Ocracoke replied to a thread BOB FW Series in Build Diaries
    I'd recommend something thicker, like the thread cutting oil that Colin mentioned. WD40 is probably going to be too light for this.
    101 replies | 24384 view(s)
No More Results
About Bad Wolf

Basic Information

Date of Birth
June 19, 1988 (31)
About Bad Wolf
Name:
Bad Wolf
Biography:
Total Noob, but trying
Location:
North Wales

Statistics


Total Posts
Total Posts
103
Posts Per Day
0.13
General Information
Last Activity
16th February 2020 11:10
Join Date
2nd January 2018
Referrals
0

4 Friends

  1. Ocracoke 
    Status
    Offline

    Team Kaizen

    Ocracoke
  2. Retroman 
    Status
    Offline

    Member

    Retroman
  3. Scottie 
    Status
    Offline

    Member

    Scottie
  4. Theo 
    Status
    Offline

    Member

    Theo
Showing Friends 1 to 4 of 4