• Ocracoke's Avatar
    Yesterday, 20:03
    They are Gimson 13.7:1 motors (https://gimsonrobotics.co.uk/categories/dc-electric-motors/products/gr-ep-45-high-power-45mm-planetary-gearmotor). Coupled with 775 motors, they are a solid, if...
    100 replies | 10974 view(s)
  • Ocracoke's Avatar
    Yesterday, 19:46
    Azriel After finding a few moments to concentrate on this one, I've got it rolling. It isn't The Honey Badger quick but it is quite controllable as a result. Thanks to having the wiring loom, motors...
    100 replies | 10974 view(s)
  • Ocracoke's Avatar
    16th June 2019, 15:15
    Jibril So the gearbox sides have been cut and the gears are on the shaft for Jibril but I've yet to make any head way in actually building it. Given the now tight timelines to RL Grantham, I may not...
    100 replies | 10974 view(s)
  • Ocracoke's Avatar
    13th June 2019, 13:32
    So the parts for the two stage reduction have arrived and I'll be cutting up the HDPE for both the gearbox and Azriel tonight. It did however strike me that I had forgotten the bearings! Bleh, they...
    100 replies | 10974 view(s)
  • Ocracoke's Avatar
    13th June 2019, 11:14
    You would need to wire it up in series (for increased voltage) or in parallel (for increased capacity) to get power to the ESC.
    110 replies | 16515 view(s)
  • Ocracoke's Avatar
    13th June 2019, 10:29
    Yes, Comet uses the 30A versions of the ESC. Not the same weight class but Jibril uses 10AWG wire with a pair of 4S 4200mAh LiFe batteries to drive both the drive and the Scythe (should probably...
    110 replies | 16515 view(s)
  • Ocracoke's Avatar
    10th June 2019, 16:58
    I was talking with Gareth (of Trolley Rage) about this and he suggested something very similar. In terms of an controller for axes, I guess you would want it to be a on-off affair to get maximum...
    100 replies | 10974 view(s)
  • Ocracoke's Avatar
    10th June 2019, 16:02
    I think you are referring to the 60A dual channel ESC? I am talking about the 40A single channel ESC, which is the next one down from the 60A. The 60A dual channel is a far more reliable controller...
    100 replies | 10974 view(s)
  • Ocracoke's Avatar
    9th June 2019, 17:33
    I think the ESC just isn't suitable for MWs full stop. It is a neat controller but it is too fragile in terms of the components out of the box but the high gearing will definitely not be helping....
    100 replies | 10974 view(s)
  • Ocracoke's Avatar
    9th June 2019, 15:12
    Yes, the new floor is going to be a one piece affair. Looking at 900mm squared 6mm polycarbonate at the moment, still not finalised the design just yet. EXR Guilford 2019 So Jibril went to EXR...
    100 replies | 10974 view(s)
  • Al_'s Avatar
    8th June 2019, 18:36
    I've not done any proper testing, but I have a mix of these and the 12v ones in Plastic Fantastic and they look about the same speed at full throttle with the bot under no load sat in the cradle....
    6 replies | 863 view(s)
  • James Williams's Avatar
    7th June 2019, 17:36
    Sorry about your floor! :oops: Looking forward to the new one. Is the floor going to be all one piece this time?
    100 replies | 10974 view(s)
  • Ocracoke's Avatar
    7th June 2019, 14:33
    Oooh, I'll hold you to that one :P I know Luke (Bad Wolf on here) does do advertising for BotFest as well. Hopefully. :D It'll run this Saturday come what may but for RL Grantham, it really...
    100 replies | 10974 view(s)
  • Ocracoke's Avatar
    7th June 2019, 12:52
    Hahhaa, will do. I've been wavering about going to EXR Guildford, RL Grantham and EXR Bolton but I think I'll be able to. If Jibil's refit with the new gearbox doesn't take too long (I should have it...
    100 replies | 10974 view(s)
  • Ocracoke's Avatar
    6th June 2019, 12:50
    Jibril I've tested the rebuilt axe mechanism and it's... fine... for now. It really will be better on the two stage gearbox as at the moment, it is a little "undertorqued" but then again, the high...
    100 replies | 10974 view(s)
  • Ocracoke's Avatar
    4th June 2019, 16:21
    Hi Colin, I know why I went for 10mm, it was the biggest HSS drill bit I had at the time and it allowed me to align everything nice and neatly. After EXR Bolton, I might ditch doing a rebuild...
    100 replies | 10974 view(s)
  • Ocracoke's Avatar
    4th June 2019, 12:41
    The bent driveshafts... probably a design flaw. They are only 10mm wide. A refit of Jibril will make them 12mm hardened steel but I might get away with 10mm hardened steel. Doesn't help they are...
    100 replies | 10974 view(s)
No More Results
About Maxamuslead

Basic Information

Date of Birth
January 1, 1994 (25)
About Maxamuslead
Name:
Mark Smith
Location:
Lincolnshire, Threekingham
Interests:
geeky stuff
Occupation:
Network Technician
Robots:
"Blacksmith" (FW) in a bag in bits "Forge Master" (FW) battle worn "Forge Master II" (FW) in CAD

Statistics


Total Posts
Total Posts
442
Posts Per Day
0.55
General Information
Last Activity
16th June 2019 16:46
Join Date
6th April 2017
Referrals
0

4 Friends

  1. Al_ 
    Status
    Offline

    Member

    Al_
  2. James Williams 
    Status
    Offline

    Roboteer

    James Williams
  3. Ocracoke 
    Status
    Online

    Team Kaizen

    Ocracoke
  4. R9000 
    Status
    Offline

    Roboteer

    R9000
Showing Friends 1 to 4 of 4