Tab Content
  • Ocracoke's Avatar
    Yesterday, 23:21
    Following on from the last post, I've been busy. Tada! I'll be running out tomorrow to get some M10x100mm bolts or something to screw the motor mounts down with along with some coarse...
    208 replies | 137814 view(s)
  • Ocracoke's Avatar
    Yesterday, 01:24
    Jibril So yeah, this weekend didn't go to plan. Managed to get the drive templates made but in cutting the drive shafts, need to go outside to that really and it has been too wet to do so. Still, I...
    208 replies | 137814 view(s)
  • Ocracoke's Avatar
    15th February 2020, 15:00
    We'll see closer to the time. Had a bit of a setback here which means I can't work on it this weekend. It'll happen.
    7 replies | 452 view(s)
  • Bad Wolf's Avatar
    13th February 2020, 21:10
    Yeah im excited to hopefully have some new bots sorted by then too! I have a couple of those strip LED lights if you need them, they plug into the mains they arnt battery though. Bad Wolf
    7 replies | 452 view(s)
  • Ocracoke's Avatar
    13th February 2020, 13:48
    Nope, no deadline really. Signups are open up until the event starts.
    7 replies | 452 view(s)
  • Ocracoke's Avatar
    13th February 2020, 10:06
    Excellent, glad to hear the event is being looking forwards to! With any luck, I will have the arena's floor lifted up a little over the weekend and the pit floor painted.
    7 replies | 452 view(s)
  • Ocracoke's Avatar
    10th February 2020, 22:41
    Hahahaa, true enough! I've got a 10mm spade bit somewhere, will bear that in mind for future use.
    208 replies | 137814 view(s)
  • Bad Wolf's Avatar
    10th February 2020, 21:18
    Cant wait for the event :) Bad Wolf
    7 replies | 452 view(s)
  • Ocracoke's Avatar
    10th February 2020, 12:14
    It is time for the next BotFest event! Location St. Lukes Church Poulton Wallasey CH44 3BD Date 25th April 2020
    7 replies | 452 view(s)
  • Ocracoke's Avatar
    10th February 2020, 02:41
    Jibril The HDPE base panel has been drilled. Doing 32 holes three times over in 3, 8 and 10mm bits is nuts but there you are. Currently mocking up the motor mount bolt pattern on a 1mm sheet of...
    208 replies | 137814 view(s)
  • Ocracoke's Avatar
    9th February 2020, 00:13
    Ocracoke replied to a thread BOB FW Series in Build Diaries
    I'd recommend something thicker, like the thread cutting oil that Colin mentioned. WD40 is probably going to be too light for this.
    101 replies | 24349 view(s)
  • Ocracoke's Avatar
    4th February 2020, 22:19
    Oh gosh! I was only using the bolt to hold the wheel up, it isn't a permanent fixture! I am going to get some shaft supports and some hardened steel shafts to overcome to the bent drive shaft issue...
    208 replies | 137814 view(s)
  • Ocracoke's Avatar
    4th February 2020, 10:16
    Worth trying, I agree. The other issue then is that I don't know if the pinion gear will reach the main gear at all. I guess if it is thin enough, it won't be a problem.
    208 replies | 137814 view(s)
No More Results
About Ocracoke

Basic Information

About Ocracoke
Name:
Lucy
Biography:
A Smart Car obsessed roboteer!
Location:
Somewhere on the Wirral
Interests:
Smart Cars, programming etc
Occupation:
Something computer based
Robots:
AW: Amai, Ikari, Lafiel, Osu, Ramu / BW: Shu!, The Honey Badger / FW: Azriel / MW: Jibril, Kaizen

Signature


Team Kaizen - Build Diary for all the robots

AW: Amai, Ikari, Lafiel, Osu, Ramu
BW: Shu!, The Honey Badger
FW: Azriel
MW: Jibril, Kaizen

Statistics


Total Posts
Total Posts
1,115
Posts Per Day
0.97
General Information
Last Activity
Today 12:40
Join Date
20th December 2016
Referrals
0
Home Page
http://teamkaizen.ocracoke.org.uk/index.php

4 Friends

  1. Bad Wolf 
    Status
    Offline

    Roboteer

    Bad Wolf
  2. joebrown 
    Status
    Offline

    Roboteer

    joebrown
  3. Maxamuslead 
    Status
    Offline

    Roboteer

    Maxamuslead
  4. Theo 
    Status
    Offline

    Member

    Theo
Showing Friends 1 to 4 of 4