Register To Comment
Results 1 to 2 of 2

Thread: A200S ESC - Based upon the VESC®*-Project

  1. #1
    The A200S is a 200A 16S ESC, based upon the VESC®*-Project.
    * VESC is a registered TM, owned by Benjamin Vedder

    The A200S is now open for pre-orders!
    emiut9n.png

    Timescale:
    Preorders are going to be ordered on the 5th March if all goes well. Meaning they will be shipped out in the middle of April.

    Specs:


    • 18 FET design
    • Weight ~800g
    • Dimensions 110x105x30mm
    • Waterjet 3mm copper bus bars
    • Waterjet 10mm thick aluminium heatsinks (Stackable)
    • 8AWG cables for input and output, with choice of 8mm bullets or lugs.
    • STM32f405 Cortex M4 microcontroller
    • 6x 100v 1000uF High-Ripple United Chemi-Con Capacitors (2 internal, 4 on external board)
    • TVS protected 5v rail, suppied from receiver
    • 15-75v rating, 16s LiPo maximum (Rating at 80v (90v maximum) on the current shunt amps, so need a bit of margin to account for ringing/transients
    • 200A (13.4kW@16s) continuous for a few minutes
    • 300A (20kW@16s) burst for a few seconds
    • All standard VESC® features (CAN, SPI, Encoder/Hall support)
    • Same amazing VESC® performance with sensorless motors.
    • Designed specifically for combat use. Absolutely no heavy components on the boards which might fall off with shock.
    • Each unit is hand built and will be rigorously tested before sale using a range of motors. (100W, 2200w, 5300w, 9800W) If I have the motor you will be using then I can set it up for you before sending it.



    Testing status:
    Testing will be finished in the next few days. With just the sustained high current and high voltage tests to run.

    Current tests:
    100A continuous - Works fine.
    130A continuous - Works fine.
    150A continuous - Works fine.
    200A continuous - Waiting on motor generator pair setup
    300A burst -
    Waiting on motor generator pair setup


    ERPM Tests:
    120000ERPM - Works fine.


    VESC features:
    BLDC - Works fine.
    FOC - Works fine.
    DC - Etek testing to follow.



    I/O:
    PPM input - Works fine.
    CANBus - Works fine.
    ADC input -
    Works fine.



    Motor Tracking:
    Sensorless tracking - Works fine.
    Hall Sensors - Works fine.
    Encoder - Testing to follow.


    Motors tested:
    Turnigy Rotomax 1.2 (1.9kW) - Works fine.
    Turnigy Rotomax 50cc (5.3kW) - Works fine.
    Turnigy Rotomax 150cc (9.8kW) - Works fine.
    Revolt RV160SH 58KV (8/15kW) - Works fine.
    Etek-R - Testing Soon.


    Price:
    Preorder price is £400 /unit for everything (Heatsink, connectors, cables, extra capacitor board) + shipping.


    If you need any changes to the heatsink, like threaded mounting holes, then I can do them for free.

    Warranty:
    I will repair any that are damaged at the price of the parts and shipping. Plus a small free depending how long they take (less than £20 max). (If it is obvious that it was smashed by a weapon then it might be a bit more :P)

    Will post some pics and videos over the next few days.


    How to order
    If you would like to pre-order then please send me a pm. Or Email teamtriforceuk@gmail.com
    Last edited by TechAUmNu; 2nd March 2018 at 16:58.

  2. #2
    Last chance to pre-order an A200S, get your order in before Monday 5th March!


Register To Comment

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •