Register To Comment
Results 1 to 6 of 6

Thread: Disassembly of Argos 14.4v

  1. #1
    Deathly Hallows's Avatar
    Roboteer

    Status
    Offline
    Name
    Simon Hallows
    Robots
    Proof of concept - done Beetle "Evil K'Weevil" in detailed design phase Feather concepts next
    Location
    Scotland
    Posts
    94
    Post Thanks / Like
    Blog Entries
    11
    Hey all,

    Decided to untangle and disassemble the Argos 14.4V drills I used in my demo bot.

    In making the demo bot, I removed the battery and unscrewed the few screws holding the two sides of the case together.

    IMG_20171106_184838.jpgIMG_20171106_184929.jpg

    In the demo bot I simply took the wires off the trigger and routed out the back. After closing the case again I used it in that state.

    IMG_20171106_190107.jpg

    The battery could be easily repurposed too, this was used in the demo bot. There is a power connector which you can wire to. Should you wish to use these batteries.
    IMG_20171106_203451.jpg

    This was all done back in November. Now that Evil K'Weevil (EKW) is almost ready, I took the test bot to pieces. Thought I would also look if the motors are any good and understand if they can be reused in a Featherweight.

    Continues....

  2. #2
    Deathly Hallows's Avatar
    Roboteer

    Status
    Offline
    Name
    Simon Hallows
    Robots
    Proof of concept - done Beetle "Evil K'Weevil" in detailed design phase Feather concepts next
    Location
    Scotland
    Posts
    94
    Post Thanks / Like
    Blog Entries
    11
    Some measurements were taken back last year when I was looking for better mounts, and struggling with fitting wheels to the demo bot.

    IMG_20171108_184710.jpg

    Since then I bought a caliper gauge so I'll post these details up in an update.

    The motor comes away from the rest of the assembly quite easily.

    IMG_20180210_162101.jpg

    Removing these pins then allows the the part to be removed

    IMG_20180210_162456.jpgIMG_20180210_162509.jpg

    The toothed gear on the motors output shaft sat neatly in here.

    Am I correct in thinking this is the clutch? Though it look like gearing it's before the dial to adjust the ratio.

    It's all greased up and when removed, watch that any bearings don't come away and then get lost.
    IMG_20180210_164138.jpg

    Now I got stuck. I don't have a suitable star head driver to remove the chuck. Biggest I have is T-20 and it's a bit bigger than that.

  3. #3
    Roboteer

    Status
    Offline
    Name
    Alan
    Robots
    Pressure Point [FW] - Active Plastic Fantastic [FW] - Under Construction
    Location
    North Notts
    Posts
    75
    Post Thanks / Like
    No idea if that's the clutch or not (I'd guess its the part which selects low or high range as the 12v single speed drills don't have that on them I don't think) but if you have not yet took your other drill apart yet you might want to leave it together for now. The LH Thread screws that hold the chucks on can be really tight and leaving the drill assembled in its case gives you a lot more to hold on to when you are trying to get it undone.

  4. #4
    Deathly Hallows's Avatar
    Roboteer

    Status
    Offline
    Name
    Simon Hallows
    Robots
    Proof of concept - done Beetle "Evil K'Weevil" in detailed design phase Feather concepts next
    Location
    Scotland
    Posts
    94
    Post Thanks / Like
    Blog Entries
    11
    You could be right. I never saw a 12v they were out of stock at the time. Too late unfortunately. Other one is in same condition. What size driver do I need? I assume they are the same. I'll need to buy one.

  5. #5
    Roboteer

    Status
    Offline
    Name
    Ruairidh
    Location
    Western Isles
    Posts
    1
    Post Thanks / Like
    Assuming it's the same screw as the 12v argos drill I used a T25.

  6. #6
    Deathly Hallows's Avatar
    Roboteer

    Status
    Offline
    Name
    Simon Hallows
    Robots
    Proof of concept - done Beetle "Evil K'Weevil" in detailed design phase Feather concepts next
    Location
    Scotland
    Posts
    94
    Post Thanks / Like
    Blog Entries
    11
    I am pretty sure you are right. I found a T30 and that's too big. Ordered a set anyway.

Register To Comment

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •