Register To Comment
Results 1 to 9 of 9

Thread: BOB FW Series

  1. #1
    Member

    Status
    Offline
    Name
    Sean
    Posts
    24
    Post Thanks / Like
    After my attempt on proto BOB I'm moving on to my real first FW BOB.

    The plan for this one is a 4 wheel drive with a lifter, like S.M.I.D.S.Y. So far this is the lay out for it.
    Untitled.png
    Just need to get a linear actuator and other parts to go with it. Luckily I got some spare MDF boards to use when I get what I need just to make sure the lay out works and a rough idea on the weight, btw the drill motors I'm using are about 440g.

    Knowing my luck when I start, I got the parts I need but not the tools.

  2. #2
    Ocracoke's Avatar
    Team Kaizen

    Status
    Offline
    Name
    Michael
    Robots
    Shu! (Building) - BW / The Honey Badger - FW / Kaizen (In planning) - HW
    Location
    Somewhere on the Wirral
    Posts
    114
    Post Thanks / Like
    Looks good, have you decided on what sort of speed controllers and the shell/bodywork material you are going to use in this?
    Team Kaizen

    Shu! - BW - Build Thread
    The Honey Badger - FW - Build Thread
    Kaizen - HW (In the planning stages)

  3. #3
    Member

    Status
    Offline
    Name
    Sean
    Posts
    24
    Post Thanks / Like
    The speed controllers I'm using are Botbitz 30a ESC and the body will be made of HDPE about 10-12mm thick.

  4. #4
    Maxamuslead's Avatar
    Roboteer

    Status
    Offline
    Name
    Mark-s
    Robots
    "Blacksmith" (FW) under construction
    Location
    Lincolnshire, Threekingham
    Posts
    148
    Post Thanks / Like
    Quote Originally Posted by sean retro View Post
    The speed controllers I'm using are Botbitz 30a ESC and the body will be made of HDPE about 10-12mm thick.
    us the 85a versions as you can power 2 drill motors of 1 speed controller. so you end up 1 for each side.

  5. #5
    Ocracoke's Avatar
    Team Kaizen

    Status
    Offline
    Name
    Michael
    Robots
    Shu! (Building) - BW / The Honey Badger - FW / Kaizen (In planning) - HW
    Location
    Somewhere on the Wirral
    Posts
    114
    Post Thanks / Like
    Sounds OK although I am not sure 15a per wheel is going to be enough... I might potentially advise using a set of TZ85a speed controllers if the BotBitz controllers aren't up to the job.

    I'd also look through the build threads of Luna-Tic since this does seem similar in concept if there are any.
    Team Kaizen

    Shu! - BW - Build Thread
    The Honey Badger - FW - Build Thread
    Kaizen - HW (In the planning stages)

  6. #6
    Member

    Status
    Offline
    Name
    Sean
    Posts
    24
    Post Thanks / Like
    Quick question, does it matter what type of battery it is like Lipo, acid etc. to power the linear actuator?

  7. #7
    Ocracoke's Avatar
    Team Kaizen

    Status
    Offline
    Name
    Michael
    Robots
    Shu! (Building) - BW / The Honey Badger - FW / Kaizen (In planning) - HW
    Location
    Somewhere on the Wirral
    Posts
    114
    Post Thanks / Like
    In short, no. What does matter is how much amperage is being sent to the motor. If there is too much, you'll either burn out the controller or the motor driving the actuator.
    Team Kaizen

    Shu! - BW - Build Thread
    The Honey Badger - FW - Build Thread
    Kaizen - HW (In the planning stages)

  8. #8
    lowndsy's Avatar
    Astronaut

    Status
    Offline
    Name
    Steve Lownds
    Robots
    Flat Damon (FW)
    Location
    Derbyshire
    Posts
    129
    Post Thanks / Like
    Anything with an appropriate voltage / ampage will work so the answer is mainly no it doesn't make much difference, but the chemistry will affect obvious things like the weight and dimensions as well as characteristics like power drop off and charging speed so there probably is an "ideal" battery for your requirements.
    Last edited by lowndsy; 6th September 2017 at 13:47.

  9. #9
    Member

    Status
    Offline
    Name
    Sean
    Posts
    24
    Post Thanks / Like
    Amperage won't be a problem, got some spare fuses what we use in plugs, felling that get a different type of fuse.

Register To Comment

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •