Register To Comment
Results 1 to 6 of 6

Thread: Argos 12v Simple Value Drill Motor Mounts

  1. #1
    Shakey's Avatar
    Roboteer

    Status
    Online
    Name
    Alex
    Robots
    Far, far too many (100+).
    Location
    Fleet, UK
    Posts
    406
    Post Thanks / Like
    Argos 12v simple value drill motor mounts
    I have designed a set of mounts for the 12v argos simple value drillmotors available here: http://www.argos.co.uk/product/6161400

    More detail on the motors is available here: http://www.fightingrobots.co.uk/thre...ide-and-review

    While the drillmotors are an excellent form of drive the updated design no longer secures the motor and gearbox together independently of the drill casing. Essentially they rely on a rotating lock to keep them connected. These milled mounts lock the motor and the gearbox in place preventing them from separating.

    They are milled from 15mm HDPE and incorporate M5 threads and a locking pattern for the drill motors.

    Weight of mounts: ~60g (per pair)
    Weight with motor: ~500g
    Thread: M5
    Thread Depth: 19mm (Approx)
    Bolt spacing: 30mmx52.5mm







    Please note I am only providing mounts, you must purchase the motors directly from argos.

    Purchasing: Please head over to my webstore here, https://nutsandbots.co.uk/

    Thanks,
    Shakey
    Last edited by Shakey; 3rd November 2017 at 17:00.

  2. #2
    Deathly Hallows's Avatar
    Roboteer

    Status
    Offline
    Name
    Simon Hallows
    Robots
    Currently working on ideas, researching and working out a budget. First task a proof of concept
    Location
    Scotland
    Posts
    47
    Post Thanks / Like
    Blog Entries
    9
    Hello Shakey,

    Do you know if these fit the Argos 14.4V too? Don't have any measuring calipers to get accurate measurements. But I can give it a go with a clamp and a ruler, if you don't already know the answer.

    Part numbering is as follows:
    HRS-550S-14.4V
    P6928DC

    Visually they look identical

    Simon

  3. #3
    Shakey's Avatar
    Roboteer

    Status
    Online
    Name
    Alex
    Robots
    Far, far too many (100+).
    Location
    Fleet, UK
    Posts
    406
    Post Thanks / Like
    I've had a glance at the 14.4v ones but have never bought one to take a look inside. My gut feeling is that they're probably fine, but I'd want to take a look at some pictures of the motor + gearbox first with some measurements before I confirm that.

  4. #4
    Deathly Hallows's Avatar
    Roboteer

    Status
    Offline
    Name
    Simon Hallows
    Robots
    Currently working on ideas, researching and working out a budget. First task a proof of concept
    Location
    Scotland
    Posts
    47
    Post Thanks / Like
    Blog Entries
    9
    Please find attached some pictures of the 14.4V Argos Drill motor - so you check if compatible

    IMG_20171108_184710.jpgIMG_20171108_184802.jpgIMG_20171108_184913.jpgIMG_20171108_184821.jpg

    Hope this helps!

  5. #5
    Member

    Status
    Offline
    Name
    Nat
    Robots
    Short Circuit (HW RWs6) DELLapidated bANTtery (AW) LowMoe (AW) Several unnamed ants
    Location
    Eastleigh, Hampshire
    Posts
    147
    Post Thanks / Like
    That moulding looks to be the same then with an additional hammer gearbox fitted. does it look like that beige and black lump can come off the gearbox with the knobbly bits? See image attached. Does it look like it could split here? Has it been moulded into a single piece?
    Attached Images Attached Images

  6. #6
    Shakey's Avatar
    Roboteer

    Status
    Online
    Name
    Alex
    Robots
    Far, far too many (100+).
    Location
    Fleet, UK
    Posts
    406
    Post Thanks / Like
    If as Roboteernat says that bit above the line comes off it should be alright, looks like the same gearbox below that.

Register To Comment

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •