Search:

Type: Posts; User: Roboteernat

Page 1 of 11 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    6
    Views
    560

    Interested to know if there was an update on any...

    Interested to know if there was an update on any progress on this? :)
  2. My bot was meant to be driven invertible (sadly...

    My bot was meant to be driven invertible (sadly doesnt quite work!) but in portsmouth, my link was cut as the link wire was poking out so you could grab it. I was advised by Greg to poke the wire...
  3. As an update, i have now 2 designs of mounting...

    As an update, i have now 2 designs of mounting options with using the zink screw inserts for M5 bolts, and another design for Barrel nut or Cross Dowels for M6 mounting screws, see image.

    I can...
  4. 3d printing of metals at this time is expensive,...

    3d printing of metals at this time is expensive, seriously expensive, will take a look at it and see what i can do, Do you have a dimensional drwing to hand?

    Another alternative would be to 3d...
  5. Check out for a local makerspace as they may have...

    Check out for a local makerspace as they may have the workshop tools you require, become a member and have access to it when ever you need :)

    This is Maidstones -...
  6. Replies
    47
    Views
    12,514

    I understand. I had no feedback from the...

    I understand.

    I had no feedback from the motor position, so stick forward is drive motor forward, back, drive motor back.
    The only thing stoppuing it from going further was the chassis/floor.
    ...
  7. Replies
    47
    Views
    12,514

    Glad your recovering :) My axe is run from a...

    Glad your recovering :)

    My axe is run from a 150w? scooter motor through a 2 stage chain gearbox giving 5:1 ratio, so not powerful, however it was rnning from a 30 amp electronize esc - as i didnt...
  8. ABS is 'difficult' for most printers due to...

    ABS is 'difficult' for most printers due to warping and climate control requirements.

    PLA is great at printing but brittle.

    PETG is good rounder of both PLA and ABS, and most find it easier to...
  9. Replies
    3
    Views
    1,265

    Hi, what are the dimensions of the 12v 100w...

    Hi, what are the dimensions of the 12v 100w scooter motor? Thanks
  10. Argos drill motor mounts and other mounts.

    8364

    From Tuesday 21st August 2018 I shall have some more motor mounts in stock.

    I have had a rush of orders this past few weeks that has taken my stock to zero, last set sent out today.
    I...
  11. Argos drill motor mounts.... I have had a...

    Argos drill motor mounts....

    I have had a demand for Argos motor mounts last couple weeks, and I sold my last set that I have in stock today.
    I will however, be making more next week and can...
  12. Hi and welcome back! You will need a suitable...

    Hi and welcome back!
    You will need a suitable esc to run the motor direct from the RX, but as you want to use a contacrot, you will need something that can switch a low voltage output on/off to...
  13. Replies
    2
    Views
    367

    Most US suppliers should stock BSPP and BSPT...

    Most US suppliers should stock BSPP and BSPT (same thing (AKA)) and companies like Parker http://ph.parker.com/gb/en/fittings , SMC, and a google search fpr hydraulic fittings give several. Im in the...
  14. Replies
    22
    Views
    2,216

    I would have thought the Ragebridge were OTT for...

    I would have thought the Ragebridge were OTT for a feathweight, and a 3.3 amp battery easily handles the 3 minute battles.
  15. Replies
    2
    Views
    576

    Are you able to post pictures of the parts on...

    Are you able to post pictures of the parts on this forum as screenshots? I may be able to take a look at them for you. Will PM
  16. Replies
    31
    Views
    2,672

    if using conbolt drills, go slow and use lots of...

    if using conbolt drills, go slow and use lots of coolant. i was able to drill through 3.2mm Hardox with some cobolt drill bits from Toolstation - about £3-5 each 5mm-7 about
  17. Replies
    22
    Views
    2,216

    potentially, but what is their weight and you...

    potentially, but what is their weight and you will also need to consider the gearing.
    The google search i did shows they are a bit larger than normal drive motors, but this is not specifically your...
  18. Replies
    22
    Views
    2,216

    assuming your wanting to run these motors for...

    assuming your wanting to run these motors for drive - 2 axles, then thats 5.4kg with just the motors not to mention gearboxes :)
  19. Replies
    6
    Views
    1,215

    I would appreciate some internal pictures for...

    I would appreciate some internal pictures for looking at, i do not think i can buy it sadly :(
  20. Replies
    22
    Views
    2,216

    There is the featherTwo by Shakey, but there are...

    There is the featherTwo by Shakey, but there are programmable ones including hobbywing escs and the good ol TZ85A. Sadly the TZs are discontinued.
  21. Replies
    6
    Views
    1,215

    Has Scot-Bot got a custom made pneumatic ram for...

    Has Scot-Bot got a custom made pneumatic ram for the flipper? just been googling for some internal pictures, looks really nice, the type of machine i would love to have.... Although my wedding needs...
  22. Replies
    71
    Views
    6,949

    did you calculate the correct centre spacing for...

    did you calculate the correct centre spacing for the axles when choosing chain length? The best method would be to fit the chain then the motors down.
    not the one im looking for but this will...
  23. Replies
    6
    Views
    883

    If o remember correctly, brushed motors are 90%...

    If o remember correctly, brushed motors are 90% happy going reverse, and 100% going forwards. So by having a mirrored motor you will usually find that one goes slower causing forward to drift.
  24. Replies
    122
    Views
    14,471

    Just seent he video of F7 at manchester, cor they...

    Just seent he video of F7 at manchester, cor they legged it out with that bot in the end didnt they! need to have a wheeled trolley next to stage to wheel them out lol *takes H&S hat off*
  25. If you have access to some water pipe vice grips...

    If you have access to some water pipe vice grips they will allow you to hold the chuck as you unscrew.
    Go to screw it as if you tighten it then unscrew.
    Give the screwdriver a tap head on .

    3...
Results 1 to 25 of 254
Page 1 of 11 1 2 3 4