Search:

Type: Posts; User: Roboteernat

Page 1 of 10 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    2
    Views
    152

    Most US suppliers should stock BSPP and BSPT...

    Most US suppliers should stock BSPP and BSPT (same thing (AKA)) and companies like Parker http://ph.parker.com/gb/en/fittings , SMC, and a google search fpr hydraulic fittings give several. Im in the...
  2. Replies
    22
    Views
    1,336

    I would have thought the Ragebridge were OTT for...

    I would have thought the Ragebridge were OTT for a feathweight, and a 3.3 amp battery easily handles the 3 minute battles.
  3. Replies
    2
    Views
    315

    Are you able to post pictures of the parts on...

    Are you able to post pictures of the parts on this forum as screenshots? I may be able to take a look at them for you. Will PM
  4. Replies
    15
    Views
    1,135

    if using conbolt drills, go slow and use lots of...

    if using conbolt drills, go slow and use lots of coolant. i was able to drill through 3.2mm Hardox with some cobolt drill bits from Toolstation - about £3-5 each 5mm-7 about
  5. Replies
    22
    Views
    1,336

    potentially, but what is their weight and you...

    potentially, but what is their weight and you will also need to consider the gearing.
    The google search i did shows they are a bit larger than normal drive motors, but this is not specifically your...
  6. Replies
    22
    Views
    1,336

    assuming your wanting to run these motors for...

    assuming your wanting to run these motors for drive - 2 axles, then thats 5.4kg with just the motors not to mention gearboxes :)
  7. Replies
    6
    Views
    811

    I would appreciate some internal pictures for...

    I would appreciate some internal pictures for looking at, i do not think i can buy it sadly :(
  8. Replies
    22
    Views
    1,336

    There is the featherTwo by Shakey, but there are...

    There is the featherTwo by Shakey, but there are programmable ones including hobbywing escs and the good ol TZ85A. Sadly the TZs are discontinued.
  9. Replies
    6
    Views
    811

    Has Scot-Bot got a custom made pneumatic ram for...

    Has Scot-Bot got a custom made pneumatic ram for the flipper? just been googling for some internal pictures, looks really nice, the type of machine i would love to have.... Although my wedding needs...
  10. Replies
    70
    Views
    4,749

    did you calculate the correct centre spacing for...

    did you calculate the correct centre spacing for the axles when choosing chain length? The best method would be to fit the chain then the motors down.
    not the one im looking for but this will...
  11. Replies
    6
    Views
    637

    If o remember correctly, brushed motors are 90%...

    If o remember correctly, brushed motors are 90% happy going reverse, and 100% going forwards. So by having a mirrored motor you will usually find that one goes slower causing forward to drift.
  12. Replies
    81
    Views
    8,868

    Just seent he video of F7 at manchester, cor they...

    Just seent he video of F7 at manchester, cor they legged it out with that bot in the end didnt they! need to have a wheeled trolley next to stage to wheel them out lol *takes H&S hat off*
  13. If you have access to some water pipe vice grips...

    If you have access to some water pipe vice grips they will allow you to hold the chuck as you unscrew.
    Go to screw it as if you tighten it then unscrew.
    Give the screwdriver a tap head on .

    3...
  14. Replies
    5
    Views
    692

    thought i would just paste this here: 8167

    thought i would just paste this here:
    8167
  15. Replies
    9
    Views
    601

    The imax b6 ac version has built in mains. So...

    The imax b6 ac version has built in mains. So just uses kettle lead.
    I like the seperate PSU as it doesn’t heat up as much the actual controller as PSU is seperate. Plus less heavy if I wanted to...
  16. As a side note, just seen the email from John...

    As a side note, just seen the email from John regarding Guildford. Thank you for including information about the safety briefing time and expanding on no booking desk :) much appreciated :)
  17. There wasnt a safety briefing as far as i was...

    There wasnt a safety briefing as far as i was aware, and i got there before the 10.30 time indicated on the email. The Tshirt was in the car, turned out to use my old series 6 t-shirt in the end. I...
  18. I arrivied following the time from the email, but...

    I arrivied following the time from the email, but regarding fire exits, toilet facilities and signing in i would have thought that needed to be done.
    As for a stranger wandering off the street into...
  19. Continued - max character count reached. Axe...

    Continued - max character count reached.


    Axe chopping, driving OK ish with my lack of experience. i get shunted pushed and meet the lovely Red lobster robot who grapples with me
    8156

    Just as...
  20. Well, as its been a couple of weeks since the...

    Well, as its been a couple of weeks since the last update and of course, Portsmouth Robot extreme, i should really update with what happened!

    Let me start with Friday before the Saturdays shows......
  21. Replies
    11
    Views
    828

    You could prob loose 'some' weight by using 2wd...

    You could prob loose 'some' weight by using 2wd and a belt between drives. saves weight on motor gearbox (but gains on belt and pulleys?

    also you wouldn't need those large plates to hold the...
  22. Replies
    286
    Views
    40,379

    Looking good, shame you went able to make it to...

    Looking good, shame you went able to make it to Portsmouth. I took inspiration frim your wiring loom to build mine this morning so was able to compete in the afternoon. Thank you for the inspiration!
  23. The cnc panels I was lucky enough to have bought...

    The cnc panels I was lucky enough to have bought an A4 cutting routing machine when i was at uni, only now has it actually had some proper use!

    The base board was too large to fit on my bed so i...
  24. Replies
    10
    Views
    1,106

    Yopur location 'Somewhere on the wirral' perhaps...

    Yopur location 'Somewhere on the wirral' perhaps you could see if there is \ local makerspace near you - https://forum.hackspace.org.uk/t/chester-north-wales-wirral-hackspace/359 is just something...
  25. I cannot remember off the top of my head, but im...

    I cannot remember off the top of my head, but im uploading a test video i made a couple of nights ago

    https://youtu.be/m8Yqug4WOxw

    I am cutting it fine!
Results 1 to 25 of 242
Page 1 of 10 1 2 3 4