• T00TY_FRU1TY's Avatar
    18th January 2018, 20:55
    Most of those Chinese motors are t8f sprockets 8mm so use #40 chain
    55 replies | 1816 view(s)
  • T00TY_FRU1TY's Avatar
    18th January 2018, 16:10
    I noticed Ellis had major reliability issues using brushless in series 9. If he had trouble I'm definitely staying clear anyways.
    55 replies | 1816 view(s)
  • T00TY_FRU1TY's Avatar
    18th January 2018, 15:19
    Out of curiosity are there any brushless ESC that are commonly used or are they all custom? Again all I can find are scooter or hobby controllers.I have my brushed motors already and have no...
    55 replies | 1816 view(s)
  • T00TY_FRU1TY's Avatar
    17th January 2018, 14:48
    How big a heat sink would be needed to replace 80mm fans?
    55 replies | 1816 view(s)
  • T00TY_FRU1TY's Avatar
    17th January 2018, 13:50
    I have seen the robot claws similar spec and price (36v so no overvolting), the can bridge the motor terminals if more current needed. No moving parts
    55 replies | 1816 view(s)
  • T00TY_FRU1TY's Avatar
    17th January 2018, 11:32
    I will once I have sourced all my remaining parts. I'm with you on brushless but seems to complex to work with and a limited number is ESC choice. Besides brushless motors are plentiful and...
    55 replies | 1816 view(s)
  • T00TY_FRU1TY's Avatar
    17th January 2018, 10:34
    Awesome katch sounds like a similar drive setup to my design. I can't wait to see your build. I'm planning to start after Easter.
    55 replies | 1816 view(s)
  • T00TY_FRU1TY's Avatar
    14th January 2018, 20:29
    Wouldn't the motors be able to handle an extra 12v? I don't have to I just thought that would be acceptable for extra power Katch thats great feedback thanks
    55 replies | 1816 view(s)
  • T00TY_FRU1TY's Avatar
    14th January 2018, 19:09
    I'm tempted to over volt to 48 think cytron is 45v so yeah that ballpark. Robot claw on the same site also look good. Out of curiosity what methods are used for controlling the large spinners with...
    55 replies | 1816 view(s)
  • T00TY_FRU1TY's Avatar
    14th January 2018, 11:40
    I have experience building large and small robots at home but absolutely none with the combat robot and the kinetic shocks these machines are subjected to! You can't try before you buy and very...
    55 replies | 1816 view(s)
  • T00TY_FRU1TY's Avatar
    13th January 2018, 16:11
    All parts and spares I have purchased except weapon system and esc. Even the priciest ESC is within budget for me. What I meant by the cheap comment was all 4qd I can find are as expensive if not...
    55 replies | 1816 view(s)
  • T00TY_FRU1TY's Avatar
    12th January 2018, 22:08
    I thought the capacitors wouldn't take the kind of shocks the robots receive. Thanks for the recommendations. 4qd seem to be extortionate where I see them. Where can I source cheap ones?
    55 replies | 1816 view(s)
  • T00TY_FRU1TY's Avatar
    10th January 2018, 09:33
    Hi all I am using two my1020 24v motors overvolting to 36v. Any recommendations for speed control? I am using an ackerman steering setup so channel mixing not necessary. Would these be...
    55 replies | 1816 view(s)
No More Results
About T00TY_FRU1TY

Basic Information

About T00TY_FRU1TY
Name:
Kenneth Gibson

Statistics


Total Posts
Total Posts
23
Posts Per Day
0.17
General Information
Last Activity
19th January 2018 16:08
Join Date
7th September 2017
Referrals
0
No results to show...