Tab Content
  • maddox10's Avatar
    Yesterday, 04:36
    maddox10 replied to a thread Keyed shaft in General Chat
    Or me.
    6 replies | 236 view(s)
  • maddox10's Avatar
    18th September 2017, 09:27
    Last time I epoxy'd magnets I did make up a batch of epoxy, dabbed it in between the magnets and had the motor spin around in the lathe untiel the glue was hardened.
    7 replies | 527 view(s)
  • maddox10's Avatar
    17th September 2017, 21:17
    maddox10 replied to a thread Iskra motors in Heavyweights
    In any case, the Iskra's are European made (Slovakia) and that is reflected in build quality and pricetag.
    6 replies | 184 view(s)
  • maddox10's Avatar
    17th September 2017, 21:15
    maddox10 replied to a thread Ragebridge Question in Heavyweights
    Have a look at Ewans webshop, and ask his advice. https://gimsonrobotics.co.uk/
    8 replies | 240 view(s)
  • maddox10's Avatar
    17th September 2017, 09:55
    maddox10 replied to a thread Iskra motors in Heavyweights
    In Bullfrog the Iskra 24V 1.2Kw motors @10S were bulletproof combined with the Robot Power Sidewinder. Never had any problems with those. One disadvantage tough, they are heavy compared to...
    6 replies | 184 view(s)
  • maddox10's Avatar
    17th September 2017, 01:05
    maddox10 replied to a thread Ragebridge Question in Heavyweights
    It depends on your knowledge and/or acces to machining time. But for a beginner, an electric lifter is easy enough. If you're aquinted to industrial pneumatics, a low pressure lifter or even...
    8 replies | 240 view(s)
  • maddox10's Avatar
    16th September 2017, 18:22
    maddox10 replied to a thread Iskra motors in Heavyweights
    Any decent hydraulics suppier can help you there. Iskra's are most used on hydraulic pump groups for lorry-tail gates and such.
    6 replies | 184 view(s)
  • maddox10's Avatar
    15th September 2017, 22:54
    maddox10 replied to a thread Ragebridge Question in Heavyweights
    Yes, it will. Scooter motors are a tad bigger than battery drill motors. The MY1016 works perfectly with the Tz85A in high stall apprications. The Sidewinder survives Bosch 750, Iskra 1.2Kw...
    8 replies | 240 view(s)
  • maddox10's Avatar
    14th September 2017, 05:55
    The LiFePo4's are not under the Fuse Rule because the battery Chemistry is inherently safer than LiPo. Worst that those can do is puff up and emit a lot of smoke.
    8 replies | 260 view(s)
  • maddox10's Avatar
    13th September 2017, 22:28
    We tested a Revolt RV-100pro unsensored on 3S driving a 20kg disk on bronze bushings today. It needed a small push to get start, but it made the revs calculated. I'm really curious how it will...
    25 replies | 904 view(s)
  • maddox10's Avatar
    13th September 2017, 19:49
    4mm only? Those tooth will be stripped during the first decent acceleration. Just to give an example of forces on gears. Kashei, a feather stripped and split steel mod 2 gears , and the motor...
    25 replies | 904 view(s)
  • maddox10's Avatar
    13th September 2017, 15:12
    I hear the batteries screaming because you'll need to cram'm in with a crowbar.
    25 replies | 904 view(s)
  • maddox10's Avatar
    13th September 2017, 07:16
    I guess we have a little confusion about cells in series and cells in parallel. Good LiPo and LiFePo4 packs have balancing leads, especialy to charge each cell. That is also the reason for the...
    8 replies | 260 view(s)
  • maddox10's Avatar
    12th September 2017, 09:15
    The HPDE over a very resilient open frame isn't a bad idea , and there are some fine examples of that. Unfortunatly, never seen one done in any degree of succes in heavyweight. But don't worry...
    13 replies | 576 view(s)
  • maddox10's Avatar
    12th September 2017, 00:19
    Team RCC tried HDPE (semi)monocoque 30mm thick on Obsidian. It lasted 1 event. The HDPE welds are more brittle than the sheets, and bends tend to concentrate stress. For bulkheads, HDPE is good...
    13 replies | 576 view(s)
  • maddox10's Avatar
    6th September 2017, 07:22
    maddox10 replied to a thread Project Squirrel in Featherweights
    The XT range of connectors don't suffer from the solder overflow.
    71 replies | 8397 view(s)
No More Results
About maddox10

Basic Information

About maddox10
Occupation:
All round technician/troubleshooter

Contact


This Page
http://www.fightingrobots.co.uk/members/1160-maddox10?s=19c80a73d9a003b7e25da02eb2e87de6
Instant Messaging

Send an Instant Message to maddox10 Using...

Statistics


Total Posts
Total Posts
2,294
Posts Per Day
0.97
General Information
Last Activity
Today 05:04
Join Date
21st March 2011
Referrals
1
Page 2 of 3 FirstFirst 123 LastLast

30th December 2016


29th December 2016


27th December 2016


22nd December 2016


12th November 2016


11th November 2016


27th September 2016


14th September 2016


18th August 2016


15th August 2016


12th August 2016


9th April 2016


16th February 2016


12th February 2016


11th February 2016


4th February 2016


2nd February 2016



Page 2 of 3 FirstFirst 123 LastLast